Nissan Pathfinder. Instruction - part 983

DOOR SWITCH

RF-37

< DTC/CIRCUIT DIAGNOSIS >

C

D

E

F

G

H

I

J

L

M

A

B

RF

N

O

P

3. Check continuity between door switch harness connector and ground.

Is the inspection result normal?

YES

>> Replace BCM. Refer to 

BCS-80, "Removal and Installation"

.

NO

>> Repair or replace harness.

3.

CHECK DOOR SWITCH 

Refer to 

RF-37, "Component Inspection"

.

Is the inspection result normal?

YES

>> GO TO 4.

NO

>> Replace malfunctioning door switch. Refer to 

DLK-313, "Removal and Installation"

.

4.

CHECK INTERMITTENT INCIDENT

Refer to 

GI-49, "Intermittent Incident"

.

>> Inspection End.

Component Inspection

INFOID:0000000009764010

1.

CHECK DOOR SWITCH

1. Turn ignition switch OFF.

2. Disconnect malfunctioning door switch connector.

3. Check continuity between door switch terminals.

Is the inspection result normal?

YES

>> Inspection End.

NO

>> Replace malfunction door switch. Refer to 

DLK-313, "Removal and Installation"

.

Door switch

BCM

Continuity 

Connector

Terminal

Connector

Terminal

Driver side

B8

3

M20

96

Yes

Passenger side

B108

94

Rear LH

B18

82

Rear RH

B116

93

Door switch

Ground

Continuity 

Connector

Terminal

Driver side

B8

3

No

Passenger side

B108

Rear LH

B18

Rear RH

B116

Door switch

Condition

Continuity

Terminal

3

Ground contact is part of the 

switch.

Door switch

Pressed

No

Released

Yes

RF-38

< SYMPTOM DIAGNOSIS >

MOONROOF DOES NOT OPERATE PROPERLY

SYMPTOM DIAGNOSIS

MOONROOF DOES NOT OPERATE PROPERLY

Diagnosis Procedure

INFOID:0000000009176304

1.

 CHECK BCM POWER SUPPLY AND GROUND CIRCUIT

Check BCM power supply and ground circuit.

Refer to 

BCS-74, "Diagnosis Procedure"

.

Is the inspection result normal?

YES

>> GO TO 2.

NO

>> Repair or replace malfunctioning parts.

2.

 CHECK MOONROOF MOTOR ASSEMBLY POWER SUPPLY AND GROUND CIRCUIT

Check moonroof motor assembly power supply and ground circuit.

Refer to 

RF-27, "MOONROOF MOTOR ASSEMBLY : Component Function Check"

.

Is the inspection result normal?

YES

>> Check intermittent incident. Refer to 

GI-49, "Intermittent Incident"

.

NO

>> Repair or replace malfunctioning parts.

SUNSHADE SYSTEM DOES NOT OPERATE PROPERLY

RF-39

< SYMPTOM DIAGNOSIS >

C

D

E

F

G

H

I

J

L

M

A

B

RF

N

O

P

SUNSHADE SYSTEM DOES NOT OPERATE PROPERLY

Diagnosis Procedure

INFOID:0000000009176305

1.

CHECK BCM POWER SUPPLY AND GROUND CIRCUIT

Check BCM power supply and ground circuit. 

Refer to 

BCS-74, "Diagnosis Procedure"

.

Is the inspection result normal?

YES

>> GO TO 2.

NO

>> Repair or replace the malfunctioning parts.

2.

CHECK SUNSHADE MOTOR ASSEMBLY POWER SUPPLY AND GROUND CIRCUIT

Check sunshade motor assembly power supply and ground circuit.

Refer to 

RF-30, "SUNSHADE MOTOR ASSEMBLY : Diagnosis Procedure"

.

Is the inspection result normal?

YES

>> GO TO 3.

NO

>> Repair or replace the malfunctioning parts.

3.

CONFIRM THE OPERATION

Confirm the operation again.
Is the result normal?

YES

>> Check intermittent incident. Refer to 

GI-49, "Intermittent Incident"

.

NO

>> GO TO 1.

RF-40

< SYMPTOM DIAGNOSIS >

AUTO OPERATION DOES NOT OPERATE

AUTO OPERATION DOES NOT OPERATE

MOONROOF
MOONROOF : Diagnosis Procedure

INFOID:0000000009176306

1.

 PERFORM INITIALIZATION PROCEDURE

Perform initialization procedure. 

Refer to 

RF-25, "ADDITIONAL SERVICE WHEN REPLACING CONTROL UNIT : Special Repair Require-

ment"

.

Is the inspection result normal?

YES

>> Moonroof system is normal.

NO

>> GO TO 2.

2.

CHECK MOONROOF SWITCH

Check moonroof switch.

Refer to 

RF-32, "Diagnosis Procedure"

.

Is the inspection result normal?

YES

>> GO TO 3.

NO

>> Repair or replace the malfunctioning parts.

3.

CONFIRM THE OPERATION 

Confirm the operation again.
Is the inspection result normal?

YES

>> Check intermittent incident. Refer to 

GI-49, "Intermittent Incident"

.

NO

>> GO TO 1.

SUNSHADE
SUNSHADE : Diagnosis Procedure

INFOID:0000000009176307

1.

PERFORM INITILAZATION PROCEDURE 

Refer to 

RF-25, "ADDITIONAL SERVICE WHEN REPLACING CONTROL UNIT : Special Repair Require-

ment"

.

Is the inspection result normal?

YES

>> Sunshade system is normal.

NO

>> GO TO 2.

2.

CHECK SUNSHADE SWITCH

Check sunshade switch.

Refer to 

RF-34, "Diagnosis Procedure"

.

Is the inspection result normal?

YES

>> GO TO 3.

NO

>> Repair or replace the malfunctioning parts.

3.

CONFIRM THE OPERATION

Confirm the operation again.
Is the result normal?

YES

>> Check intermittent incident. Refer to 

GI-49, "Intermittent Incident"

.

NO

>> GO TO 1.