Nissan Pathfinder. Instruction - part 622

FRONT BUMPER

EXT-19

< REMOVAL AND INSTALLATION >

C

D

E

F

G

H

I

J

L

M

A

B

EXT

N

O

P

Section

Measurement

Minimum

Target Value

Maximum

A-A

Clearance

0.2 (0.01)

1.5 (0.06)

2.8 (0.11)

B-B

Clearance 

0.5 (0.02)

2.0 (0.08)

3.5 (0.14)

B-B

Surface height 

0.0 (0.00)

1.4 (0.06)

2.8 (0.11)

C-C

Clearance 

1.0 (0.04)

2.0 (0.08)

3.0 (0.12)

C-C

Surface height

0.0 (0.00)

1.0 (0.04)

2.0 (0.08)

D-D

Clearance

0.0 (0.00)

0.0 (0.00)

0.0 (0.00)

D-D

Surface height

0.0 (0.00)

0.0 (0.00)

0.0 (0.00)

E-E

Clearance

-0.3 (-0.01)

0.0 (0.00)

0.7 (0.03)

F-F

Clearance

0.0 (0.00)

1.0 (0.04)

2.0 (0.08)

G-G

Clearance

-1.0 (-0.04)

0.0 (0.00)

1.0 (0.04)

H-H

Clearance

-0.8 (-0.03)

0.0 (0.00)

0.8 (0.03)

H-H

Surface height

-0.3 (-0.01)

0.7 (0.03)

1.7 (0.07)

J-J

Clearance

0.5 (0.02)

1.5 (0.06)

2.5 (0.10)

EXT-20

< REMOVAL AND INSTALLATION >

REAR BUMPER

REAR BUMPER

Exploded View

INFOID:0000000009176336

Removal and Installation

INFOID:0000000009176337

REMOVAL

CAUTION:

Bumper fascia is made of resin. Use care when handling to prevent damage. Avoid contact with oily

substances.
1. Open back door.
2. Remove the rear combination lamps (LH/RH). Refer to 

EXL-149, "Removal and Installation"

.

1.

Rear bumper side bracket (LH)

2.

Rear bumper reinforcement 
support (LH)

3.

Rear bumper fascia lower brack-
et (LH)

4.

Rear bumper reinforcement

5.

Rear bumper energy absorber 6.

Rear sonar sensor harness (if 
equipped)

7.

Sonar sensors (if equipped)

8.

Tow hitch cover finisher

9.

Rear bumper fascia molding

10. Rear bumper fascia

11. Rear bumper fascia lower 

bracket (RH)

12. Rear bumper reinforcement sup-

port (RH)

13. Rear bumper side bracket (RH)

AWKIA2252ZZ

REAR BUMPER

EXT-21

< REMOVAL AND INSTALLATION >

C

D

E

F

G

H

I

J

L

M

A

B

EXT

N

O

P

3. Remove the rear bumper fascia clips (A) and screws (B) (LH/

RH).

4. Partially remove the rear wheel house protectors. Refer to 

EXT-29, "REAR WHEEL HOUSE PROTEC-

TOR : Removal and Installation"

.

5. Remove the bumper fascia side upper screws (A) (LH/RH). 

6. Remove rear bumper fascia lower side bolts (A) (LH/RH).

7. Remove the rear bumper fascia lower rear clips (A).

8. Disconnect the harness connector from rear sonar sensors (if equipped).

ALKIA2414ZZ

ALKIA2415ZZ

ALKIA2420ZZ

ALKIA2904ZZ

EXT-22

< REMOVAL AND INSTALLATION >

REAR BUMPER

9. Pull rear bumper fascia outward away from vehicle to release

from rear bumper side brackets (LH/RH).

: Pawl

10. Remove the rear bumper fascia.

CAUTION:

When removing rear bumper fascia, two people are required to avoid damaging.

11. Remove the following parts (if necessary) after removing rear bumper fascia.

• Rear bumper fascia reflectors (LH/RH)

• Rear sonar sensors (if equipped)

• Rear bumper fascia molding

12. Remove rear bumper energy absorber.

INSTALLATION

Installation is in the reverse order of removal.

NOTE:

• The following table shows the specified values for checking normal

installation status.

• Fitting adjustment cannot be performed.

mm (in)

ALKIA2905ZZ

ALKIA2906ZZ

Section

Measurement

Minimum

Target Value

Maximum

A-A

Clearance

0.0 (0.00)

1.0 (0.04)

2.0 (0.08)

B-B

Clearance

0.0 (0.00)

1.5 (0.06)

3.0 (0.12)

C-C

Clearance

3.0 (0.12)

5.0 (0.20)

7.0 (0.28)

C-C

Surface height

-1.0 (-0.04)

1.0 (0.04)

3.0 (0.12)

D-D

Clearance

0.0 (0.00)

1.0 (0.04)

2.0 (0.08)

D-D

Surface height

-0.2 (0.01)

0.8 (0.03)

1.8 (0.07)

E-E

Clearance

5.0 (0.12)

7.0 (0.28)

9.0 (0.35)