Nissan Pathfinder. Instruction - part 526

 

  Index      Nissan     Nissan Pathfinder (2014 year) - Service and Repair Instruction

 

Search            copyright infringement  

 

 

 

 

 

 

 

  

 

Content   ..  524  525  526  527   ..

 

 

Nissan Pathfinder. Instruction - part 526

 

 

EC-410

< DTC/CIRCUIT DIAGNOSIS >

[VQ35DE]

P2127, P2128 APP SENSOR

P2127, P2128 APP SENSOR

DTC Logic

INFOID:0000000009178336

DTC DETECTION LOGIC

DTC CONFIRMATION PROCEDURE

1.

PRECONDITIONING

If DTC Confirmation Procedure has been previously conducted, always perform the following before conduct-

ing the next test.

1. Turn ignition switch OFF and wait at least 10 seconds.

2. Turn ignition switch ON.

3. Turn ignition switch OFF and wait at least 10 seconds.

TESTING CONDITION:

Before performing the following procedure, confirm that battery voltage is more than 8 V at idle.

>> GO TO 2.

2.

PERFORM DTC CONFIRMATION PROCEDURE

1. Start engine and let it idle for 1 second.

2. Check DTC.
Is DTC detected?

YES

>> Proceed to 

EC-411, "Diagnosis Procedure"

.

NO

>> INSPECTION END

Diagnosis Procedure

INFOID:0000000009178337

1.

CHECK APP SENSOR 2 POWER SUPPLY

1. Disconnect accelerator pedal position (APP) sensor harness connector.

2. Turn ignition switch ON.

3. Check the voltage between APP sensor harness connector and ground.

Is the inspection result normal?

YES

>> GO TO 4.

NO

>> GO TO 2.

2.

CHECK APP SENSOR 2 POWER SUPPLY CIRCUIT

1. Turn ignition switch OFF.

DTC No.

CONSULT screen terms

(Trouble diagnosis content)

DTC detecting condition

Possible cause

P2127

APP SEN 2/CIRC
(Throttle/Pedal position sen-
sor/switch “E” circuit low)

An excessively low voltage from the APP 
sensor 2 is sent to ECM.

• Harness or connectors

(APP sensor 2 circuit is open or shorted.)
[CKP sensor (POS) circuit is shorted.]
(Refrigerant pressure sensor circuit is 
shorted.)
(EVAP control system pressure sensor 
circuit is shorted.)

• Accelerator pedal position sensor

(APP sensor 2)

• Crankshaft position sensor (POS)
• EVAP control system pressure sensor
• Refrigerant pressure sensor
• Sensor power supply 2 circuit

P2128

APP SEN 2/CIRC
(Throttle/Pedal position sen-
sor/switch “E” circuit high)

An excessively high voltage from the APP 
sensor 2 is sent to ECM.

APP sensor

Ground

Voltage (V)

Connector

Terminal

E31

5

Ground

Approx. 5

P2127, P2128 APP SENSOR

EC-411

< DTC/CIRCUIT DIAGNOSIS >

[VQ35DE]

C

D

E

F

G

H

I

J

K

L

M

A

EC

N

P

O

2. Disconnect ECM harness connector.

3. Check the continuity between APP sensor harness connector and ECM harness connector.

Is the inspection result normal?

YES

>> GO TO 3.

NO

>> Repair open circuit.

3.

CHECK SENSOR POWER SUPPLY 2 CIRCUIT

Check sensor power supply 2 circuit. Refer to 

EC-450, "Diagnosis Procedure"

.

Is the inspection result normal?

YES

>> Perform the trouble diagnosis for power supply circuit.

NO

>> Repair or replace error-detected parts.

4.

CHECK APP SENSOR 2 GROUND CIRCUIT

1. Turn ignition switch OFF.

2. Disconnect ECM harness connector.

3. Check the continuity between APP sensor harness connector and ECM harness connector.

4. Also check harness for short to ground and short to power.
Is the inspection result normal?

YES

>> GO TO 5.

NO

>> Repair open circuit, short to ground or short to power in harness or connectors.

5.

CHECK APP SENSOR 2 INPUT SIGNAL CIRCUIT

1. Check the continuity between APP sensor harness connector and ECM harness connector.

2. Also check harness for short to ground and short to power.
Is the inspection result normal?

YES

>> GO TO 6.

NO

>> Repair open circuit, short to ground or short to power in harness or connectors.

6.

CHECK APP SENSOR

Check APP sensor. Refer to 

EC-412, "Component Inspection"

.

Is the inspection result normal?

YES

>> Check intermittent incident. Refer to 

GI-49, "Intermittent Incident"

.

NO

>> Replace accelerator pedal assembly. Refer to 

ACC-3, "Removal and Installation"

.

Component Inspection

INFOID:0000000009178338

1.

CHECK ACCELERATOR PEDAL POSITION SENSOR

1. Reconnect all harness connectors disconnected.

2. Turn ignition switch ON.

3. Check the voltage between ECM harness connector terminals under the following conditions.

APP sensor

ECM

Continuity

Connector

Terminal

Connector

Terminal

E31

5

E16

103

Existed

APP sensor

ECM

Continuity

Connector

Terminal

Connector

Terminal

E31

1

E16

116

Existed

APP sensor

ECM

Continuity

Connector

Terminal

Connector

Terminal

E31

6

E16

98

Existed

EC-412

< DTC/CIRCUIT DIAGNOSIS >

[VQ35DE]

P2127, P2128 APP SENSOR

Is the inspection result normal?

YES

>> INSPECTION END

NO

>> Replace accelerator pedal assembly. Refer to 

ACC-3, "Removal and Installation"

.

ECM

Condition

Voltage (V)

Connector

+

–

Terminal

E16

97

100

Accelerator pedal

Fully released

0.5 - 1.0

Fully depressed

4.2 - 4.8

98

116

Fully released

0.25 - 0.50

Fully depressed

2.0 - 2.5

P2135 TP SENSOR

EC-413

< DTC/CIRCUIT DIAGNOSIS >

[VQ35DE]

C

D

E

F

G

H

I

J

K

L

M

A

EC

N

P

O

P2135 TP SENSOR

DTC Logic

INFOID:0000000009178339

DTC DETECTION LOGIC

NOTE:

If DTC P2135 is displayed with DTC P0643, first perform the trouble diagnosis for DTC P0643. Refer to

EC-354, "DTC Logic"

.

DTC CONFIRMATION PROCEDURE

1.

PRECONDITIONING

If DTC Confirmation Procedure has been previously conducted, always perform the following before conduct-

ing the next test.

1. Turn ignition switch OFF and wait at least 10 seconds.

2. Turn ignition switch ON.

3. Turn ignition switch OFF and wait at least 10 seconds.

TESTING CONDITION:

Before performing the following procedure, confirm that battery voltage is more than 8 V at idle.

>> GO TO 2.

2.

PERFORM DTC CONFIRMATION PROCEDURE

1. Start engine and let it idle for 1 second.

2. Check DTC.
Is DTC detected?

YES

>> Proceed to 

EC-414, "Diagnosis Procedure"

.

NO

>> INSPECTION END

Diagnosis Procedure

INFOID:0000000009178340

1.

CHECK THROTTLE POSITION SENSOR POWER SUPPLY

1. Disconnect electric throttle control actuator harness connector.

2. Turn ignition switch ON.

3. Check the voltage between electric throttle control actuator harness connector and ground.

Is the inspection result normal?

YES

>> GO TO 2.

NO

>> Repair open circuit, short to ground or short to power in harness or connectors.

2.

CHECK THROTTLE POSITION SENSOR GROUND CIRCUIT

1. Turn ignition switch OFF.

2. Disconnect ECM harness connector.

3. Check the continuity between electric throttle control actuator harness connector and ECM harness con-

nector.

DTC No.

CONSULT screen terms

(Trouble diagnosis content)

DTC detecting condition

Possible cause

P2135

TP SENSOR-B1
(Throttle/Pedal position 
sensor/switch “A” / “B” volt-
age correlation)

Rationally incorrect voltage is sent to ECM 
compared with the signals from TP sensor 1 
and TP sensor 2.

• Harness or connector

(TP sensor 1 or 2 circuit is open or shorted.)

• Electric throttle control actuator

(TP sensor 1 or 2)

Electric throttle control actuator

Ground

Voltage (Approx.)

Connector

Terminal

F50

1

Ground

5 V

 

 

 

 

 

 

 

Content   ..  524  525  526  527   ..