Nissan Pathfinder. Instruction - part 1188

CVT OIL WARMER

TM-211

< REMOVAL AND INSTALLATION >

[CVT: RE0F10E]

C

E

F

G

H

I

J

K

L

M

A

B

TM

N

O

P

CVT OIL WARMER

Exploded View

INFOID:0000000009177681

Removal and Installation

INFOID:0000000009177682

REMOVAL

WARNING:

Do not remove the radiator cap when the engine is hot. Serious burns could occur from high pressure

coolant escaping from the radiator. Wrap a thick cloth around the cap. Slowly turn it a quarter turn to

allow built-up pressure to escape. Carefully remove the cap by turning it all the way.

CAUTION:

Perform this step engine is cold.

NOTE:

When removing components such as hoses, tubes/lines, etc., cap or plug openings to prevent fluid from spill-

ing.
1. Drain engine coolant from radiator. Refer to 

CO-11, "Changing Engine Coolant"

.

2. Remove CVT water hose from CVT oil warmer. Refer to  

TM-206, "Exploded View"

.

3. Remove CVT fluid cooler hose from CVT oil warmer. Refer to  

TM-208, "Exploded View"

.

4. Remove CVT oil warmer.
5. Remove bracket.

INSTALLATION

Installation is in the reverse order of removal.

Inspection

INFOID:0000000009177683

INSPECTION AFTER INSTALLATION

• Check for CVT fluid leakage. Refer to 

TM-185, "Inspection"

.

• Start and warm up the engine. Visually check that there is no leakage of engine coolant and CVT fluid.

ADJUSTMENT AFTER INSTALLATION

Adjust CVT fluid level. Refer to 

TM-187, "Adjustment"

.

Transaxle assembly

CVT oil warmer

O-ring

: Always replace after every disassembly.

: N·m (kg-m, ft-lb)

JSDIA3624GB

TM-212

< REMOVAL AND INSTALLATION >

[CVT: RE0F10E]

PLUG

PLUG

Description

INFOID:0000000009177684

Replace the O-ring if oil leaks from the plug.

Exploded View

INFOID:0000000009177685

Removal and Installation

INFOID:0000000009177686

NOTE:

Replace the O-rings if oil leaks from the plugs.

REMOVAL

Remove the plugs and O-rings.

INSTALLATION

Installation is in the reverse order of removal.

CAUTION:

• Do not reuse O-ring.

• Apply Genuine NISSAN CVT Fluid NS-3 to O-ring.

Inspection and Adjustment

INFOID:0000000009177687

INSPECTION AFTER INSTALLATION

Check for CVT fluid leakage. Refer to 

TM-185, "Inspection"

.

ADJUSTMENT AFTER INSTALLATION

Adjust CVT fluid level. Refer to 

TM-187, "Adjustment"

.

Transaxle assembly

O-ring

Plug

: Always replace after every disassembly.

: N·m (kg-m, ft-lb)

: Apply CVT fluid

JSDIA3622GB

TRANSMISSION ASSEMBLY

TM-213

< UNIT REMOVAL AND INSTALLATION >

[CVT: RE0F10E]

C

E

F

G

H

I

J

K

L

M

A

B

TM

N

O

P

UNIT REMOVAL AND INSTALLATION

TRANSMISSION ASSEMBLY

Exploded View

INFOID:0000000009177688

2WD Models

JSDIA3922GB

Gusset

Transaxle assembly

O-ring

CVT fluid charging pipe

Water outlet

CVT fluid charging cap

: For the tightening torque, refer to 

TM-214, "Removal and Installation"

.

: Always replace after every disassembly.

: N·m (kg-m, ft-lb)

: N·m (kg-m, in-lb)

: Apply petroleum jelly

TM-214

< UNIT REMOVAL AND INSTALLATION >

[CVT: RE0F10E]

TRANSMISSION ASSEMBLY

4WD Models

Removal and Installation

INFOID:0000000009177689

REMOVAL

WARNING:

Do not remove the radiator cap when the engine is hot. Serious burns could occur from high pressure

coolant escaping from the radiator. Wrap a thick cloth around the cap. Slowly turn it a quarter turn to

allow built-up pressure to escape. Carefully remove the cap by turning it all the way.

CAUTION:

• Perform when the engine is cold.

• When replacing TCM and transaxle assembly as a set, replace transaxle assembly first and then

replace TCM. Refer to 

TM-81, "Description"

.

NOTE:

When removing components such as hoses, tubes/lines, etc., cap or plug openings to prevent fluid from spill-

ing.
1. Remove the engine and transaxle with the front suspension member as a unit. Refer to 

EM-102, "2WD :

Removal and Installation"

 (2WD) or 

EM-107, "4WD : Removal and Installation"

 (4WD).

2. Disconnect the transaxle harness connectors.
3. Disconnect the CVT oil warmer water hoses from engine side. Refer to 

TM-206, "Removal and Installa-

tion"

.

4. Remove the CVT fluid charging pipe.

JSDIA3923GB

Gusset

Transaxle assembly

O-ring

CVT fluid charging pipe

Water outlet

CVT fluid charging cap

: For the tightening torque, refer to 

TM-214, "Removal and Installation"

.

: Always replace after every disassembly.

: N·m (kg-m, ft-lb)

: N·m (kg-m, in-lb)

: Apply petroleum jelly