Nissan Pathfinder. Instruction - part 1178

OVERDRIVE CONTROL SWITCH

TM-171

< DTC/CIRCUIT DIAGNOSIS >

[CVT: RE0F10E]

C

E

F

G

H

I

J

K

L

M

A

B

TM

N

O

P

Is the inspection result normal?

YES

>> GO TO 5.

NO

>> Repair or replace malfunctioning parts.

5.

CHECK CIRCUIT BETWEEN CVT SHIFT SELECTOR AND COMBINATION METER (PART 1)

1. Turn ignition switch OFF.

2. Disconnect combination meter connector.

3. Check continuity between CVT shift selector harness connector terminal and combination meter harness

connector terminal.

Is the inspection result normal?

YES

>> GO TO 6.

NO

>> Repair or replace malfunctioning parts.

6.

CHECK CIRCUIT BETWEEN CVT SHIFT SELECTOR AND COMBINATION METER (PART 2)

Check continuity between CVT shift selector harness connector terminal and ground.

Is the inspection result normal?

YES

>> GO TO 7.

NO

>> Repair or replace malfunctioning parts.

7.

CHECK COMBINATION METER INPUT SIGNAL

1. Connect all of disconnected connectors.

2. Turn ignition switch ON.

3. Select “Data Monitor” in “METER/M&A”.

4. Select “O/D OFF SW”.

5. Check that “O/D OFF SW” turns ON/OFF when overdrive control switch is operated. Refer to 

MWI-24,

"Reference Value"

.

Is the inspection result normal?

YES

>> Check intermittent incident. Refer to 

GI-49, "Intermittent Incident"

.

NO

>> Replace combination meter. Refer to 

MWI-82, "Removal and Installation"

.

Component Inspection

INFOID:0000000009177627

1.

CHECK OVERDRIVE CONTROL SWITCH

CVT shift selector

—

Continuity

Connector

Terminal

M78

2

Ground

Existed

CVT shift selector

Combination meter

Continuity

Connector

Terminal

Connector

Terminal

M78

1

M24

52

Existed

CVT shift selector

—

Continuity

Connector

Terminal

M78

1

Ground

Not existed

TM-172

< DTC/CIRCUIT DIAGNOSIS >

[CVT: RE0F10E]

OVERDRIVE CONTROL SWITCH

Check continuity between wires of shift selector handle  .

Is the inspection result normal?

YES

>> INSPECTION END

NO

>> Replace shift selector handle. Refer to 

TM-189,

"Exploded View"

.

Condition

Continuity

Overdrive control switch is de-
pressed

Existed

Overdrive control switch is released

Not existed

JSDIA2795ZZ

OD OFF INDICATOR LAMP

TM-173

< DTC/CIRCUIT DIAGNOSIS >

[CVT: RE0F10E]

C

E

F

G

H

I

J

K

L

M

A

B

TM

N

O

P

OD OFF INDICATOR LAMP

Component Function Check

INFOID:0000000009177628

1.

CHECK OD OFF INDICATOR LAMP FUNCTION

Check OD OFF indicator lamp turns ON for approx. 2 seconds when ignition switch turns ON.
Is the inspection results normal?

YES

>> INSPECTION END

NO

>> Go to 

TM-173, "Diagnosis Procedure"

.

Diagnosis Procedure

INFOID:0000000009177629

1.

CHECK DTC (TCM)

With CONSULT

1. Turn ignition switch ON.

2. Check “Self Diagnostic Results” in “TRANSMISSION”.
Is any DTC detected?

YES

>> Check DTC detected item. Refer to 

TM-60, "DTC Index"

.

NO

>> GO TO 2.

2.

CHECK DTC (COMBINATION METER)

With CONSULT

Check “Self Diagnostic Results” in “METER/M&A”.
Is any DTC detected?

YES

>> Check DTC detected item. Refer to 

MWI-29, "DTC Index"

.

NO

>> GO TO 3.

3.

CHECK COMBINATION METER INPUT/OUTPUT SIGNAL

With CONSULT

1. Shift the selector lever to “D” position.

2. Select “Data Monitor” in “METER/M&A”.

3. Select “O/D OFF IND”.

4. Check that “O/D OFF IND” turns ON/OFF when overdrive control switch is operated. Refer to 

MWI-24,

"Reference Value"

.

Is the inspection result normal?

YES

>> Replace combination meter. Refer to 

MWI-82, "Removal and Installation"

.

NO

>> GO TO 4.

4.

CHECK TCM INPUT/OUTPUT SIGNAL

With CONSULT

1. Select “Data Monitor” in “TCM”.

2. Select “SPORT MODE IND”.

3. Check that “SPORT MODE IND” turns ON/OFF when overdrive control switch is operated. Refer to 

TM-

48, "Reference Value"

.

Is the inspection result normal?

YES

>> Replace combination meter. Refer to 

MWI-82, "Removal and Installation"

.

NO

>> Check overdrive control switch circuit. Refer to 

TM-170, "Diagnosis Procedure"

.

TM-174

< DTC/CIRCUIT DIAGNOSIS >

[CVT: RE0F10E]

TOW MODE SYSTEM

TOW MODE SYSTEM

Component Function Check

INFOID:0000000009177630

1.

CHECK TOW MODE SWITCH FUNCTION

Check that TOW mode indicator lamp turns ON/OFF when tow mode switch is operated.
Is the inspection results normal?

YES

>> INSPECTION END

NO

>> Go to 

TM-174, "Diagnosis Procedure"

.

Diagnosis Procedure

INFOID:0000000009177631

1.

CHECK DTC (TCM) 

With CONSULT

1. Start the engine.

2. Check “Self Diagnostic Results” in “TRANSMISSION”.
Is any DTC detected?

YES

>> Check DTC detected item. Refer to 

TM-60, "DTC Index"

.

NO

>> GO TO 2.

2.

CHECK DTC (COMBINATION METER) 

With CONSULT

Check “Self Diagnostic Results” in “METER/M&A”.
Is any DTC detected?

YES

>> Check DTC detected item. Refer to 

MWI-29, "DTC Index"

.

NO

>> GO TO 3.

3.

CHECK COMBINATION METER INPUT/OUTPUT SIGNAL

With CONSULT

1. Select “Data Monitor” in “METER/M&A”.

2. Select “TOW MODE IND”.

3. Check that “TOW MODE IND” turns ON/OFF when tow mode switch is operated. Refer to 

MWI-24, "Ref-

erence Value"

.

Is the inspection result normal?

YES

>> Replace the combination meter. Refer to 

MWI-82, "Removal and Installation"

.

NO

>> GO TO 4.

4.

CHECK TOW MODE SWITCH CIRCUIT

1. Turn ignition switch OFF.

2. Disconnect tow mode switch connector.

3. Turn ignition switch ON.

4. Check voltage between tow mode switch harness connector terminals.

Is the inspection result normal?

YES

>> GO TO 5.

NO

>> GO TO 6.

5.

CHECK TOW MODE SWITCH

Check tow mode switch. Refer to 

TM-175, "Component Inspection"

.

Is the inspection result normal?

YES

>> Check intermittent incident. Refer to 

GI-49, "Intermittent Incident"

.

Tow mode switch

Voltage

(Approx.)

Connector

+

−

Terminal

M6

1

4

Battery voltage