Nissan X-Trail 32. Instruction - part 2010

STR-40

< REMOVAL AND INSTALLATION >

STARTER MOTOR

2.

Remove air duct (inlet). Refer to 

EM-308, "Removal and Installation"

.

3.

Disconnect ECM harness connectors 

.

4.

Remove harness bracket mounting bolts 

.

5.

Remove harness fixing clip 

.

6.

Remove battery tray mounting bolts 

, and then remove battery

tray .

7.

Remove electric throttle control actuator. Refer to 

EM-314, "Removal and Installation"

.

CAUTION:

Cover the openings to avoid entry of foreign materials.

8.

Remove air inlet hose 2. Refer to 

EM-314, "Removal and Installation"

.

9.

Remove “B” terminal nut and “B” terminal harness.

10. Remove “S” terminal nut and “S” terminal harness.
11. Remove starter motor mounting bolts.

12. Remove starter motor upward from the vehicle.

CAUTION:

Never contact with and damage surrounding parts when removing starter motor from the vehicle.

INSTALLATION

Note the following items, and then install in the reverse order of removal.

CAUTION:

• Be careful to insert pin 

 of starter motor 

 into hole 

 of

transmission housing 

. (CVT models)

: Vehicle front

JMBIA4643ZZ

: Vehicle front

JMBIA4644ZZ

JMBIA4639ZZ

STARTER MOTOR

STR-41

< REMOVAL AND INSTALLATION >

C

D

E

F

G

H

I

J

K

L

M

A

STR

N

P

O

• Be careful to insert pin 

 of transmission housing 

 into hole

 of starter motor 

. (MT models)

• Be careful to tighten “B” terminal nut to the specified torque.
• Erase the starter operation counter when the starter motor for models with STOP/START SYSTEM is

replaced. Refer to 

EC-960, "Work Procedure"

.

• Replace the engine restart relay and the fuel pump relay when the starter motor for models with

STOP/START SYSTEM is replaced.

JMBIA4640ZZ

STR-42

< SERVICE DATA AND SPECIFICATIONS (SDS) 

SERVICE DATA AND SPECIFICATIONS (SDS)

SERVICE DATA AND SPECIFICATIONS (SDS)

SERVICE DATA AND SPECIFICATIONS (SDS)

Starter Motor

INFOID:0000000010957651

Engine

QR

MR

R9M

Type

M000TB0071

S114-971

0 001 A01 527

0 001 A02 157

MITUBISHI make

HITACHI make

BOSCH make

Reduction gear type

System voltage

[V]

12

No-load

Terminal voltage

[V]

11

11

—

—

Current

[A]

Less than 90

Less than 110

—

—

Revolution

[rpm]

More than 2,370

More than 3,300

—

—

Minimum diameter of commuta-
tor

[mm (in)]

28.0 (1.102)

28.0 (1.102)

—

—

Minimum length of brush

[mm (in)]

5.5 (0.217)

10.5 (0.413)

—

—

Brush spring tension

[N (kg,

lb)]

15.0 - 20.4

(1.53 - 2.08, 3.37 - 

4.58)

16.2 (1.65, 3.6)

—

—

Clearance between bearing 
metal and armature shaft

[mm (in)]

Less than 0.2 

(0.008)

Less than 0.2 

(0.008)

—

—

Clearance “L” between pinion 
front edge and pinion stopper

[mm (in)]

—

0.3 - 2.5

(0.012 - 0.098)

—

—

Movement “L” in height of pinion 
assembly

[mm (in)]

0.5 - 2.0

(0.020 - 0.079)

—

—

—

TM-1

TRANSMISSION & DRIVELINE

C

E

F

G

H

I

J

K

L

M

SECTION 

TM

A

B

TM

N

O

P

CONTENTS

TRANSAXLE & TRANSMISSION

6MT: RS6F94R

PRECAUTION ..............................................

13

PRECAUTIONS ..................................................

13

Precaution for Supplemental Restraint System 
(SRS) "AIR BAG" and "SEAT BELT PRE-TEN-
SIONER" .................................................................

13

Precaution Necessary for Steering Wheel Rota-
tion After Battery Disconnect ...................................

13

Precaution for Procedure without Cowl Top Cover 

....

14

Precautions for Removing Battery Terminal  ...........

14

Service Notice or Precautions for Instruction Tran-
saxle ........................................................................

15

PREPARATION ...........................................

16

PREPARATION ..................................................

16

Special Service Tools ..............................................

16

Commercial Service Tools  ......................................

18

Lubricant or/and Sealant  .........................................

20

SYSTEM DESCRIPTION  .............................

21

COMPONENT PARTS  .......................................

21

Component Parts Location ......................................

21

STRUCTURE AND OPERATION .......................

22

Sectional View .........................................................

22

System Description  .................................................

23

DTC/CIRCUIT DIAGNOSIS  .........................

24

POSITION SWITCH ............................................

24

Component Function Check ....................................

24

Diagnosis Procedure ...............................................

24

Component Inspection  ............................................

24

SYMPTOM DIAGNOSIS  ..............................

26

NOISE, VIBRATION AND HARSHNESS 
(NVH) TROUBLESHOOTING  ............................

26

NVH Troubleshooting Chart  ....................................

26

PERIODIC MAINTENANCE  ........................

27

M/T OIL ..............................................................

27

Inspection ................................................................

27

Draining ...................................................................

27

Refilling ....................................................................

27

REMOVAL AND INSTALLATION  ...............

28

M/T SHIFT SELECTOR .....................................

28

Exploded View .........................................................

28

Removal and Installation  .........................................

28

CONTROL LINKAGE ........................................

31

Exploded View .........................................................

31

Removal and Installation  .........................................

31

Inspection ................................................................

35

POSITION SWITCH  ..........................................

36

Exploded View .........................................................

36

Removal and Installation  .........................................

36

Inspection ................................................................

37

DIFFERENTIAL SIDE OIL SEAL ......................

38

Exploded View .........................................................

38

Removal and Installation  .........................................

38

Inspection ................................................................

39

AIR BREATHER ................................................

40

Exploded View .........................................................

40

Removal and Installation  .........................................

40

UNIT REMOVAL AND INSTALLATION ......

41

TRANSAXLE ASSEMBLY ................................

41

Exploded View .........................................................

41

Removal and Installation  .........................................

41

Inspection ................................................................

42

UNIT DISASSEMBLY AND ASSEMBLY  ....

43