Nissan Qashqai J11. Instruction - part 708

WATER HOSE

TM-407

< REMOVAL AND INSTALLATION >

[CVT: RE0F10D]

C

E

F

G

H

I

J

K

L

M

A

B

TM

N

O

P

-

Place dial indicator (A) on the pellet 

 and measure the elonga-

tion from the initial state.

4.

If out of standard, replace heater thermostat.

INSPECTION AFTER INSTALLATION

Start the engine and check visually that there is no leakage of engine coolant.

Standard

: Refer to 

TM-421, "Heater Thermostat"

.

JSDIA3662ZZ

TM-408

< REMOVAL AND INSTALLATION >

[CVT: RE0F10D]

FLUID COOLER SYSTEM

FLUID COOLER SYSTEM

Exploded View

INFOID:0000000010589397

Transaxle side

Vehicle side

JSDIA5320GB

Transaxle assembly

Copper washer

Fluid cooler tube A

Fluid cooler tube B 

Hose clamp

Fluid cooler hose A

CVT oil warmer

: Always replace after every disassembly.

: N·m (kg-m, ft-lb)

JSDIA5319GB

FLUID COOLER SYSTEM

TM-409

< REMOVAL AND INSTALLATION >

[CVT: RE0F10D]

C

E

F

G

H

I

J

K

L

M

A

B

TM

N

O

P

Removal and Installation

INFOID:0000000010589398

REMOVAL

NOTE:
When removing components such as hoses, tubes/lines, etc., cap or plug openings to prevent fluid from spill-
ing.

1.

Remove front bumper. Refer to 

EXT-19, "Removal and Installation"

.

2.

Remove engine under cover. Refer to 

EXT-35, "ENGINE UNDER COVER : Removal and Installation"

.

3.

Remove the battery mounting bracket assembly and battery mounting bracket. Refer to 

PG-154,

"Exploded View"

.

4.

Remove the harness bracket mounting nuts (

) and remove

the harness bracket 

 from the vehicle.

5.

Remove hose clamps of CVT cooler hose F and B to remove the
hose on the CVT oil warmer side.

6.

Remove hose clamp (

) of CVT fluid cooler 

 to remove the

hose on the CVT fluid cooler side.

7.

Remove bracket mounting nut (

) to remove fluid cooler hose

B, C, E, and F together with fluid cooler tube assembly A.

Bumper reinforcement

Bracket

Bracket

CVT fluid cooler 

Hose clamp

Fluid cooler hose D

Fluid cooler tube assembly B

Bumper reinforcement lower

Fluid cooler hose E

Fluid cooler hose C

Bracket

Fluid cooler tube assembly A

Fluid cooler hose B

Fluid cooler hose F

Front side member LH

Transaxle assembly

CVT oil warmer

Fluid cooler tube A

: Always replace after every disassembly.

: N·m (kg-m, in-lb)

: Vehicle front

JSDIA6041ZZ

JSDIA5412ZZ

JSDIA5413ZZ

TM-410

< REMOVAL AND INSTALLATION >

[CVT: RE0F10D]

FLUID COOLER SYSTEM

8.

Remove the bracket mounting bolts (

) and remove the CVT

fluid cooler from the vehicle.

9.

Remove fluid cooler hose D.

10. Remove the fluid cooler tube assembly B from CVT fluid cooler.
11. Remove hose clamp of fluid cooler hose A to remove the hose

on the CVT oil warmer side.

12. Remove fluid cooler tube A and fluid cooler tube B.

INSTALLATION

Note the followings and Installation is in the reverse order of removal.

CAUTION:

• Be careful not to damage CVT fluid cooler.
• Never reuse hose clamps.

Transaxle side

Refer to the followings when installing CVT fluid cooler tubes.
• When installing fluid cooler tube A 

 and fluid cooler tube B 

 to

transaxle assembly, contact fluid cooler tubes stopper 

 and 

 to

transaxle case.

• Refer to the followings when installing fluid cooler hose.

• Refer to the followings when installing hose clamp.

CAUTION:

Hose clamp should not interfere with the bulge of tube.

Vehicle side

JSDIA5414ZZ

JSDIA5321ZZ

Hose 

Installation side 

tube 

Direction of paint mark

Hose insertion depth 

(A)

Fluid cooler 
hose A

CVT oil warmer

Frontward

Hose end reaches the 
end of tube.

CVT fluid cooler 
tube B

Align with the paint 
marks on the CVT fluid 
cooler tube B

SCIA7203E

Hose 

Installation side 

tube 

Hose clamp 

Direction of tab

Clamping position

Fluid cooler 
hose A

CVT oil warmer

Frontward

5 - 9 MM. (0.20 - 0.35 
in) (A) from hose end

CVT fluid cooler 
tube B

JSDIA2424ZZ