Index Nissan Nissan Qashqai J11 - Service and Repair Instruction

Search copyright infringement

Content .. 2274 2275 2276 2277 ..

Nissan Qashqai J11. Instruction - part 2276

BODY MAINTENANCE

MA-139

< PERIODIC MAINTENANCE >

C

D

E

F

G

H

I

J

K

L

M

B

MA

N

O

A

BODY MAINTENANCE

LOCKS, HINGES AND HOOD LATCH

LOCKS, HINGES AND HOOD LATCH : Lubricating

INFOID:0000000010355652

SEAT BELT, BUCKLES, RETRACTORS, ANCHORS AND ADJUSTERS

SEAT BELT, BUCKLES, RETRACTORS, ANCHORS AND ADJUSTERS : Inspection

INFOID:0000000010355653

For front seat belt illustration. Refer to

SE-25, "Exploded View"

.

For rear seat belt illustration. Refer to

SE-34, "Exploded View"

CAUTION:

• After any collision, inspect all seat belt assemblies, including retractors and other attached hard-

wares (I.e. anchor bolt, guide rail set). Nissan recommends to replace all seat belt assemblies in use
during a collision, unless not damaged and properly operating after minor collision.
Also inspect seat belt assemblies not in use during a collision, and replace if damaged or improperly
operating.
Seat belt pre-tensioner should be replaced even if the seat belts are not in use during a frontal colli-
sion where the driver and passenger air bags are deployed.

• If any component of seat belt assembly is questionable, do not repair.

Replace as seat belt assembly.

• If webbing is cut, frayed, or damaged, replace belt assembly.
• Never oil tongue and buckle.
• Use a genuine NISSAN seat belt assembly.
For details, refer to

SE-21, "Inspection Procedure"

in SB section.

• Check anchors for loose mounting
• Check belts for damage
• Check retractor for smooth operation
• Check function of buckles and tongues when buckled and released

BODY CORROSION

BODY CORROSION : Checking Body Corrosion

INFOID:0000000010355654

Visually check body panels for collision damage (scratches, chipping, rubbing, etc.) or damage to the anti-cor-
rosion materials. In particular, check the following locations.

HEMMED PANELS

Hood front end, door lower end, trunk lid rear end, etc.

PANEL JOINT

PART

TYPE 1

TYPE 2

TYPE 3

TYPE 4

HOOD

DLK-150, "Exploded

DLK-328, "Exploded

DLK-461, "Exploded

DLK-597, "Exploded

HOOD LOCK

DLK-177, "Exploded

DLK-357, "Exploded

DLK-488, "Exploded

DLK-626, "Exploded

FRONT DOOR

DLK-161, "Exploded

DLK-341, "Exploded

DLK-472, "Exploded

DLK-610, "Exploded

FRONT DOOR LOCK

DLK-180, "Exploded

DLK-361, "Exploded

DLK-491, "Exploded

DLK-630, "Exploded

REAR DOOR

DLK-166, "Exploded

DLK-346, "Exploded

DLK-477, "Exploded

DLK-615, "Exploded

REAR DOOR LOCK

DLK-184, "Exploded

DLK-365, "Exploded

DLK-495, "Exploded

DLK-634, "Exploded

BACK DOOR

DLK-171, "Exploded

DLK-351, "Exploded

DLK-482, "Exploded

DLK-620, "Exploded

BACK DOOR LOCK

DLK-188, "Exploded

DLK-369, "Exploded

DLK-499, "Exploded

DLK-638, "Exploded

MA-140

< PERIODIC MAINTENANCE >

CHASSIS MAINTENANCE

• Check transaxle surrounding area (oil seal and plug etc.)for fluid

leakage.

• If anything is found, repair or replace damaged parts and adjust

CVT fluid level. Refer to

MA-141, "CVT FLUID (RE0F10D) :

.

CVT FLUID (RE0F10D) : Replacement

INFOID:0000000011497349

CAUTION:

• Always use shop paper. Never use shop cloth.
• Replace a drain plug gasket with new ones at the final stage of the operation when installing.
• Use caution when looking into the drain hole as there is a risk of dripping fluid entering the eye.
• After replacement, always perform CVT fluid leakage check.

1.

Select “Data Monitor” in “TRANSMISSION” using CONSULT.

2.

Select “FLUID TEMP” and confirm that the CVT fluid temperature is 40

°

C (104

°

F) or less.

3.

Check that the selector lever is in the “P” position, then completely engage the parking brake.

4.

Lift up the vehicle.

5.

Remove the drain plug and drain the CVT fluid from the oil pan. Refer to

TM-400, "Exploded View"

6.

Install the drain plug to oil pan.

CAUTION:

Drain plug gasket use the old one.

7.

Remove the overflow plug

from converter housing.

8.

Install the charging pipe set (KV311039S0) (A) into the overflow
plug hole.

CAUTION:

Tighten the charging pipe by hand.

9.

Install the ATF changer hose (B) to the charging pipe.

CAUTION:

Press the ATF changer hose all the way onto the charging
pipe until it stops.

10. Fill approximately 3 liter (2-5/8 lmp qt) of the CVT fluid.
11. Remove the ATF changer hose and charging pipe, then install

the overflow plug.
NOTE:
Perform this work quickly because CVT fluid leaks.

12. Lift down the vehicle.

13. Start the engine.

SMA146B

Recommended fluid and fluid capacity

: Refer to

MA-64, "Fluids and Lubricants"

: Vehicle front

JSDIA3714ZZ

JSDIA3713ZZ

SERVICE DATA AND SPECIFICATIONS (SDS)

MA-141

< SERVICE DATA AND SPECIFICATIONS (SDS)

C

D

E

F

G

H

I

J

K

L

M

B

MA

N

O

A

SERVICE DATA AND SPECIFICATIONS (SDS)

SERVICE DATA AND SPECIFICATIONS (SDS)

DRIVE BELT (HRA2DDT)

DRIVE BELT (HRA2DDT) : Drive Belts

INFOID:0000000010503187

DRIVE BELT (MR20DD)

DRIVE BELT (MR20DD) : Drive Belt

INFOID:0000000010735713

DRIVE BELT

DRIVE BELT (K9K)

DRIVE BELT (K9K) : Drive Belt

INFOID:0000000010503189

DRIVE BELT

DRIVE BELT (R9M)

DRIVE BELT (R9M) : Drive Belts

INFOID:0000000010503190

DRIVE BELT

ENGINE COOLANT (HRA2DDT)

ENGINE COOLANT (HRA2DDT) : Periodical Maintenance Specification

INFOID:0000000010503191

ENGINE COOLANT CAPACITY (APPROXIMATE)

Unit:

(Imp qt)

ENGINE COOLANT (MR20DD)

ENGINE COOLANT (MR20DD) : Periodical Maintenance Specification

INFOID:0000000010735716

ENGINE COOLANT CAPACITY (APPROXIMATE)

Unit:

(Imp qt)

ENGINE COOLANT (K9K)

Tension of drive belt

Auto adjustment by auto-tensioner

Tension of drive belt

Belt tension is not necessary, as it is automatically adjusted by drive belt auto-tensioner.

Tension of drive belt

Auto adjustment by auto-tensioner

Tension of drive belt

Belt tensioning is not necessary, as it is automatically adjusted by drive belt auto-tensioner.

Engine coolant capacity (With reservoir tank at “MAX” level)

6.5 (5-3/4)

Reservoir tank engine coolant capacity (At “MAX” level)

0.8 (3/4)

Engine coolant capacity (With reservoir tank at “MAX” level)

CVT models

7.4 (6-1/2)

M/T models

7.1 (6-1/4)

Reservoir tank engine coolant capacity (At “MAX” level)

0.8 (3/4)

MA-142

< SERVICE DATA AND SPECIFICATIONS (SDS)

SERVICE DATA AND SPECIFICATIONS (SDS)

ENGINE COOLANT (K9K) : Periodical Maintenance Specification

INFOID:0000000010503192

ENGINE COOLANT CAPACITY (APPROXIMATE)

Unit:

(Imp qt)

ENGINE COOLANT (R9M)

ENGINE COOLANT (R9M) : Periodical Maintenance Specification

INFOID:0000000010503193

ENGINE COOLANT CAPACITY (APPROXIMATE)

Unit:

(Imp qt)

ENGINE OIL (HRA2DDT)

ENGINE OIL (HRA2DDT) : Periodical Maintenance Specification

INFOID:0000000010503194

ENGINE OIL CAPACITY (APPROXIMATE)

Unit:

(lmp qt)

ENGINE OIL (MR20DD)

ENGINE OIL (MR20DD) : Periodical Maintenance Specification

INFOID:0000000010735717

ENGINE OIL CAPACITY (APPROXIMATE)

Unit:

(lmp qt)

ENGINE OIL (K9K)

ENGINE OIL (K9K) : Periodical Maintenance Specification

INFOID:0000000010503195

ENGINE OIL CAPACITY (APPROXIMATE)

Unit: ·(Imp

qt)

ENGINE OIL (R9M)

ENGINE OIL (R9M) : Periodical Maintenance Specification

INFOID:0000000010503196

ENGINE OIL CAPACITY (APPROXIMATE)

Engine coolant capacity (With reservoir tank at “MAX” level)

6.3 (5-1/2)

Reservoir tank engine coolant capacity (At “MAX” level)

0.8 (3/4)

Engine coolant capacity (With reservoir tank at “MAX” level)

M/T models

7.3 (6-3/8)

CVT models

7.9 (7)

Reservoir tank engine coolant capacity (At “MAX” level)

0.8 (3/4)

Drain and refill

With oil filter change

4.6 (4)

Without oil filter change

4.3 (3-3/4)

Dry engine (Overhaul)

5.6 (4-7/8)

Drain and refill

With oil filter change

3.8 (3-3/8)

Without oil filter change

3.6 (3-1/8)

Dry engine (Overhaul)

4.4 (3-7/8)

With oil filter change

4.55 (4)

Without oil filter change

4.39 (3-7/8)

Dry engine (overhaul)

4.71 (4-1/8)

Content .. 2274 2275 2276 2277 ..