Isuzu N-Series. Service manual - part 1290

 

  Index      Isuzu     Isuzu N-Series - service and repair manual

 

Search            

 

 

 

 

 

 

 

 

 

Content   ..  1288  1289  1290  1291   ..

 

 

Isuzu N-Series. Service manual - part 1290

 

 

Washing of battery
If the exterior parts of the battery are dirty, use warm water to wash them. To
prevent corrosion, apply a thin layer of Vaseline or grease to the surface of the
terminal stud of the battery.

Specific gravity of the battery electrolyte
If the electrolyte hydrometer reads 1.26 at 20益, it can be deemed that the bat鄄
tery is fully charged.
If the specific gravity is lower than 1.23, the battery needs recharging.

138

OWNER爷S MANUAL

JAC High end Light Trucks

Recommended brands of lubricants and diesels

For the best performance and the longest service life of your vehicle, proper brands of lube oils and diesels should be
used according to the recommendation in the list below.

Location

Oil products recommended

Quantity

Engine oil sump

diesel engine lube oil

Above CE class

For the viscosity, refer to the list of engine lube oil viscosity vs. temperature

6

Gearbox

Summer: GL-4/85W-90

2.7

Winter: GL-4/80W-90

Power steering gear

Auto gearbox oil

As needed

Rear axle

Medium load automotive gear oil

Class GL-4

For the viscosity, refer to the list of gear oil viscosity vs. temperature

3.5

Brake fluid reservoir

DOT3 or DOT4

As needed

Clutch fluid reservoir

DOT3 or DOT4

As needed

Wheel bearings

Multipurpose grease or lithium-based wheel bearing grease

As needed

Intermediate bearing of drive shaft

No.2 or 3 universal lithium-based grease for automobiles

As needed

Clutch yoke

No.2 or 3 universal lithium-based grease for automobiles

As needed

Drive shaft slide bushing

Foss EPT-2.5 grease

As needed

Driving universal joint

Foss EPT-2.5 grease

As needed

Engine cooling system

Glycol anti-freezing fluid

with preservative

As needed

Fuel tank

Summer: No.0 quality light diesel

Winter: No.-10 quality light diesel

Ambient temperature below -30益: No.-35 quality light diesel

92

139

140

Lube oils must be selected and used carefully according to the lubricated points, and it is especially important to select
proper lube oil viscosity according to the ambient temperature;
Table of diesel viscosity for diesel engines

Table of gear oil viscosity

Infill diesel engine lube oil

Infill gear oil

Lubrication

渊single class冤

enviromment

temperature

渊multilevel冤

Correlation of engine lube oil

viscosity vs ambient temperature

OWNER爷S MANUAL

JAC High end Light Trucks

渊single class冤

Correlation of engine lube oil

viscosity vs ambient temperature

渊multilevel冤

enviromment

temperature

List of lubrication points

Steering gear

drag link

clutch fluid&brake fluid

king steering pin

front hub bearing

tie rod end

engine

rear leaf spring pin

rear hub bearing

differential

rear leaf spring lifting lug pin

king steering pin

front hub bearing
tie rod end

gearbox

drive shaft universal joint

drive shaft universal joint

drive shaft slide bushing

rear leaf spring pin

drive shaft universal joint
rear hub bearing

rear leaf spring lifting lug pin

at the first 1000km

every other month or 3000km

every 6 months or 18000km

every 8 months or 24000km

every other year or 36000km

Lubrication points

replace

W:wheel bearing grease

check, infill or lubricate

C: multipurpose grease

E: engine oil

M: lithium-based grease

G: gear oil

B: brake fluid

141

Guide to lubrication
Change of the engine oil
Remove the drain plug in the lower part of the oil sump, and drain away the
engine oil in the engine crankcase.
Retighten the drain plug after complete drainage of the engine oil in the engine
crankcase and the fuel filter.
Afterwards, pour the new engine oil of the specified grade into the engine
crankcase through the oil filling port in the cylinder head. Note: Hot engine oil
may scald skins, so please wait for the engine to cool down before draining oil.

The engine oil surface level in the oil sump is measured by the dipstick fixed on
the inner side of the engine. When measuring, the engine should not be run鄄
ning, wait for the oil surface to become still before pulling out the dipstick, and
wipe off the oil from the dipstick with clean cotton cloth. Dip the dipstick into the
oil sump again to the bottom, and then pull it out to check the oil level. There
are two scale lines on the dipstick, the engine oil level should not be below the
lower scale, or there will be difficult oil supply. But the engine oil level should
not be over the upper scale line, otherwise there will occur carbon deposition,
fumes and oil permeation, etc. Therefore, apart from constant attention to the

142

OWNER爷S MANUAL

JAC High end Light Trucks

normality of the engine oil pressure, the engine oil surface level should be
checked before driving out and at an interval of 300-500km.

Replacement of gearbox oil
Screw off the drain hole plug (D) in the bottom of the gearbox casing, drain the
oil out of the gearbox casing. Then, infill the specified lubricant oil into the
gearbox casing through the level inspection hole, until the oil level goes up to
the screw plug (L)of the level inspection hole.

143

144

Replacement of differential oil
Screw off the drain hole plug (D) in the bottom of the rear axle case to drain the
gear oil in it, infill the specified gear oil into the rear axle case through the level
inspection hole, until the oil level goes up to the screw plug (L)of the level in鄄
spection hole.

Replacement of the greases for the front and rear hub bearings
Replacement of the greases for the front and left hub bearings needs disas鄄
sembly and reassembly of the bearings, so please entrust the authorized JAC
service stations to do that. Proper maintenance and driving can prolong the ve鄄
hicle service life, but also can improve the fuel and oil economic efficiency.

OWNER爷S MANUAL

JAC High end Light Trucks

Replacement of steering oil and fluid
Exhaust fluid
1. Jack up the front axle off the ground completely.
2. Remove the oil pipes (2 pieces) between the steering gear and the power
steering oil reservoir.
3. After the steering fluid is drained off, start the engine in short time, turn the
steering wheel right and left to its limit positions without over 15 seconds, until
the residual fluid is completely drained from the steering pipes.

New fluid fill-up
1. Fix the removed oil pipe in the oil pot and infill the specified power steering
fluid.
2. Fill in the power steering fluid up between the scale marks in the oil pot.
Take care that the fluid surface sinks in parallel with the fill-up, so as to keep a
stable level against any air trapped in.
3. Lower down the front wheels onto the ground, start the engine into idle
speed for several minutes, and rotate the steering wheel right and left.
4. Check the level against the scale mark, and add some more if needed.

145

 

 

 

 

 

 

 

Content   ..  1288  1289  1290  1291   ..