|
|
on the front of the cable control unit will
WARNING
turn on. Refer to the table in the "Charging
system failure" chapter in the "Power
205) The charging current level ("Level 1"
sources that can be used" section.
/ "Level 2" / "Level 3", etc.) can only be
210) The "Mode 2" charge cable must be
changed using the Uconnect™ system
connected to a dedicated circuit that is
display (see "Settings" in the"Vehicle
not shared with other devices that absorb
mode" paragraph in the "Multimedia"
electrical energy.
section). The default charge level set is
211) Do not insert fingers or objects in the
"Level 3". For countries in which the 13A
cable charging connector.
"Mode 2" charge cable can be used,
212) The high-voltage battery must only
202
F0S1053
if the domestic power socket IS NOT
be charged through approved, earthed
CERTIFIED, it is recommended to set
domestic sockets or at a public charging
replace the protective cover of the
"Level 4" charge to the maximum, which
station using the supplied Mode 3
charging port;
corresponds to approx. 10A. For the list of
charge cable (for versions/markets where
country-specific cable types refer to what
provided).
close the charging flap, making sure
is indicated in the "Mode 2 cable variant
213) Keep the charging flap closed when
it locks properly;
table".
the charging port is not in use.
roll up the charging cable correctly,
206) The set level applies indifferently to
repositioning the protective cover
both AC home charging (Mode 2) and
correctly on the charging connector
charging from an AC public charging
IMPORTANT
station (Mode 3). It is therefore always
(where provided). When rolling up,
advisable to check that the level is set as
take care not to damage the cable.
67) Do not charge if the external
desired for the actual charging type that is
Then store the cable together with the
about to be carried out.
temperature is -30°C or lower, as charging
is likely to take longer and the charging
charging kit.
207) Incorrect setting of the charge current
device may be damaged.
intensity can overload or overheat the
68) Do not leave the car or the charging
mains power supply of the domestic
WARNING Before disconnecting the
cable in areas where the external
power socket. Fire hazard. Before charging
temperature is below -40°C as they may
charging connector, make sure that
from other domestic sockets, adjust the
be damaged.
the doors are unlocked. If the door is
charge current intensity to the mains. If
69) In cold temperatures, the charging
you do not know the mains, set to the
locked, the charging connector locking
cable may become stiff. Therefore, be
lowest level. Never use extension cords for
system does not allow disconnection.
careful not to apply excessive force to the
charging.
charging cable as it may be damaged.
208) Incorrect connection between
70) Do not use personal generators to
connector and charging terminals
charge the high-voltage battery. This may
constitutes a fire hazard!
cause fluctuations in charging and the
209) During normal operation, the
voltage may be insufficient, resulting in
domestic power socket can overheat. In
damage to the car system.
the case of extreme overheating, the
charge is interrupted and the warning LED
202
71) Charging the high-voltage battery
QUICK DOMESTIC
using incorrect or damaged sockets, or
CHARGING
charging cables and not following the
prescribed charging procedures may
PROCEDURE FROM
cause short circuits, fire and potential risk
THE WALLBOX
of damage to the electrical system of the
car.
CHARGING STATION
72) Avoid leaving the battery for several
WARNING The wallbox charging
days with the charge indicator at or near
station domestic charging station must
zero. The high-voltage battery may be
damaged.
be installed by qualified personnel
73) You do not need to wait until the
after checking the domestic electrical
203
F0S1271
battery level is low to recharge. The
system. For information on available
performance of the battery is optimal when
NOTE The wallbox charging station
wallbox charging stations, contact a
it is charged regularly.
configuration may vary depending on
Fiat Dealership.
74) Charging the high-voltage battery may
the country where the car is sold.
take longer if the temperature of the high-
NOTE The electrical system of the
voltage battery is high or low.
The high-voltage battery of your car
75) During charging, especially with fast
house must be checked regularly by
can be charged by directly connecting
charging, battery cooling components may
qualified personnel.
the charging cable to the wallbox
be activated. Therefore, it is normal to hear
The maximum charging current value
noises during this operation.
charging station or using the Mode 3
is automatically set by the device,
charge cable (for versions/markets
depending on the building's electrical
where provided).
system.
For the characteristics of the "Mode 3"
For the charging procedure, refer to the
cable, refer to the "Power sources that
"Alternating current (AC) charging at
can be used - Mode 3 cable" chapter.
home" chapter.
Charging with wallbox charging station,
fig. 203, allows to reach, from a
domestic user, a higher charge power
than the charge achieved using a
domestic socket: the charging time,
as a consequence, is significantly
reduced.
203
CHARGING
PROCEDURE FROM
PUBLIC CHARGING
STATION (AC)
214) 212) 216)
The high-voltage battery of the car can
be charged by directly connecting the
charging cable of the public charging
stations or using the Mode 3 charge
204
F0S1207
206
F0S1052
cable (for versions/markets where
remove the protective cover of the
provided).
charging port and attach it to the
For the characteristics of the "Mode 3"
device;
cable, refer to the "Power sources that
grasp the charging cable, remove the
can be used - Mode 3 cable" chapter.
protective covers on both sides of the
To charge, proceed as follows:
cable (where provided). Hold the first
park the car safely (transmission in
charging connector and insert it into
position "P" - Park);
the charging port on the car until you
engage the electric parking brake;
hear a click indicating that it is locked;
turn the ignition device to the STOP
charging starts automatically if there
position;
205
F0S1054
is no programming on the Uconnect™
remove the charging cable
system (see chapter "Charging
fig. 204 (where provided) located
open the charging flap fig. 206
by
functions"). If necessary, the public
inside a special bag in the luggage
pressing on the area indicated by the
charging station must be enabled;
compartment or inside the special
arrow;
follow the manufacturer's instructions
container below the luggage
and warnings when using the charging
compartment floor;
station;
remove any dust that may have built
the 5 LEDs with a steady green light
up on the charging connector and on
will light up momentarily to indicate the
the charging port;
correct insertion of the plug;
plug the charging connector into the
during charging, the LEDs will light
socket of the public charging station,
on with green flashing/green steady
fig. 205;
light depending on the state of charge
204
of the battery portion indicated by the
state of charge of the battery portion
replace the protective cover of the
LED. The fixed green light indicates that
indicated by the LED. The fixed green
charging port;
the battery portion is fully charged.
light indicates that the battery portion is
close the charging flap, making sure
NOTE The charging procedure is
fully charged).
it locks properly;
interrupted when opening the bonnet:
roll up the charging cable correctly,
a dedicated message will be shown
repositioning the protective covers on
on the instrument panel display. The
both sides of the cable correctly (take
charge will be reactivated when the
care not to damage the cable when
bonnet is closed correctly.
rolling it up). Then store the cable.
NOTE In some countries the "Mode 3"
cable is not available.
WARNING
WARNING Always connect the
connector first to the socket on the
207
F0S1220
214) The charging current level ("Level 1"
/ "Level 2" / "Level 3", etc.) can only be
public charging station and then to the
changed using the Uconnect™ system
car.
DISCONNECTING THE
display (see "Settings" in the"Vehicle
"MODE 3" CHARGING
mode" paragraph in the "Multimedia"
CABLE
section). The default charge level set is
WARNING Before leaving the car, it is
To complete the charging, proceed as
"Level 3". The set level applies indifferently
advisable to lock the doors by pressing
to both AC home charging (Mode 2) and
follows:
the button
on the key. If it is not
charging from an AC public charging
unlock the doors of the car allowing
possible to lock the doors by pressing
station (Mode 3). It is therefore always
the charging cable to unlock;
advisable to check that the level is set as
the button
on the key, lock the
if charging is in progress, press
desired for the actual charging type that is
doors by pressing the button on the
button (B) fig. 207;
about to be carried out.
driver's side door handle.
215) The high-voltage battery must only
disconnect the cable from the
be charged through approved, earthed
charging port of the car and put the
domestic sockets or at a public charging
END OF CHARGING
protective cover (where provided) back
station using the supplied Mode 3
PROCEDURE
on the connector;
charge cable (for versions/markets where
The charging procedure ends when all
provided).
unplug the cable from the charging
the LEDs (A) fig. 207, located next to
216) Keep the charging flap closed when
port on the public charging station
the charging port, will light up steady
the charging port is not in use.
and put the protective cover (where
green (during the charging phase, on
provided) back correctly on the two-
the other hand, the LEDs will light up
colour connector;
flashing/fixed green according to the
205
CHARGING FROM
the charging port, will light up steady
green (during the charging phase, on
PUBLIC CHARGING
the other hand, the LEDs will light up
STATION (DC)
flashing/fixed green according to the
PROCEDURE -
state of charge of the battery portion
MODE 4
indicated by the LED. The fixed green
light indicates that the battery portion is
76) 77) 78) 79) 80) 81)
fully charged).
The high-voltage battery of the car can
be charged by directly connecting the
208
F0S1052
charging cable of DC (direct current)
public charging stations.
remove the protective cover of the
To charge, proceed as follows:
charging port and attach it to the
park the car safely (transmission in
device;
position "P" - Park);
grasp the charging cable, hold the
engage the electric parking brake;
first charging connector and insert it
turn the ignition device to the STOP
into the charging port on the car until
position;
you hear a click indicating that it is
209
F0S1220
take the charging cable from the
locked;
charging station;
the 5 LEDs with a steady green light
DISCONNECTING THE
remove any dust that may have
will light up momentarily to indicate the
"MODE 4" CHARGING
accumulated on the charging
correct insertion of the plug;
CABLE
connector and charging port;
lock the doors by pressing the button
To complete the charging, proceed as
open the charging flap fig. 208 by
on the key;
follows:
pressing on the area indicated by the
charging starts automatically.
unlock the doors of the car allowing
arrow;
If necessary, the public charging
the charging cable to unlock;
station must be enabled; follow the
if charging is in progress, press
manufacturer's instructions and
button (B) fig. 209 on the charging port;
warnings when using the charging
disconnect the cable from the
station.
charging port of the car and put the
END OF CHARGING
protective cover (where provided) back
on the connector;
PROCEDURE
The charging procedure ends when all
the LEDs (A) fig. 209, located next to
206
put the cable on the public charging
charging speed is necessary to preserve
NOTE To restore correct operation of
station;
the battery.
the system, contact the Fiat Dealership.
replace the protective cover of the
charging port;
CHARGING CABLE
close the charging flap, making sure
it locks properly.
EMERGENCY
UNLOCK
(for versions/markets, where provided)
IMPORTANT
If the charging cable does not unlock at
the end of the charging procedure, you
76) Using "Fast Charge - Mode 4" can
can unlock it manually.
accelerate the battery degradation
If, after closing and opening the doors
210
F0S1208
process.
77) If fast charging is not required,
by pressing the relevant buttons
standard (AC) charging is always
CHARGING
/
located on the key and after
preferred. This maximises battery life by
FUNCTIONS
having pressed the button near the
ensuring the best performance of the car
charging port, it is still not possible to
over time.
CHARGING SCHEDULE
remove the charge cable from the
78) The charging times in "Fast Charge -
Two charging modes are available:
Mode 4" are referred to up to 80% of the
socket on the car, it is possible to
immediate and scheduled.
state of charge of the high-voltage battery
act manually by operating a special
The two charging modes can be
in standard environmental conditions
emergency unlocking device located
(25°C).
selected in two ways:
on the right side of the boot and
79) Charging times in extreme weather
via the dedicated smartphone app
performing the operations described
conditions can increase by as much as
(refer to the chapter "Connected
several minutes due to the intervention
below:
Services - Uconnect Services" in the
of the high-voltage battery management
acting inside the boot, remove the
system, which ensures optimal regulation
"Multimedia" section) (where provided)
cap (A) fig. 210;
of the battery temperature to prevent
by means of the Uconnect™
pull the release cord (B) fig. 210 to
possible damage.
system.
manually unlock the actuator of the
80) The charging speed slows down when
The page available on the Uconnect™
the state of charge of the high-voltage
charging port;
system can be used to set charging
battery exceeds 80%.
disconnect the charging cable;
81) The battery charging time can increase
check that the release cord is
times when the car will be charged
by a few minutes in case of very cold/hot
via Mode 2 or Mode 3. By acting on
correctly repositioned inside its
outside temperatures, many quick
the Uconnect™ system display and
housing, then reinsert the cap (A)
charging sessions, high frequency of use
selecting the "Charging schedule"
of "Fast Charge - Mode 4" charging or
fig. 210.
function on the screen under the
ageing of the battery. This reduction in
207
"Vehicle" page (fig. 211) you can set
sections. Charging will start at the
the start and end time at which the
selected time.
high-voltage battery is to be charged.
While the system is waiting for the
B
The end time of each charging interval
charging interval, the LED lights up (A)
can be set as "charge to completion",
fig. 212 (located next to the charging
in which case the end time will be
port) and the LEDs (B) will illuminate in
A
deselected. For more information,
a blue light sequence.
see "Settings" in the "Vehicle mode"
When charging is in progress
paragraph in the "Multimedia" section).
according to a programmed time, LED
NOTE DC recharging (Mode 4) does
(A) fig. 212 and LEDs (B) will light up
212
F0S1065
not include hourly programming.
green flashing/fixed depending on the
state of charge of the battery portion
indicated by the LED. The fixed green
light indicates that the battery portion is
fully charged.
B
If the charging cable is inserted and
there are no selected charging times on
the Uconnect™ system, charging will
A
start immediately (see chapter "Using
immediate charging").
To perform scheduled charging with
213
F0S1067
211
F0S1194
"charge to completion" option, the
USING SCHEDULED
plug must be inserted within 5 minutes
USING IMMEDIATE
CHARGING
before the scheduled start.
CHARGING
After programming and selecting the
You can move on to the next
When the charging cable is inserted
desired charging intervals (up to a
scheduled charging interval while an
and there are no charging schedules
maximum of three), plug in the charging
immediate charging operation is in
selected, the cable will be locked and
cable, following the charging procedure
progress by unlocking the ports and
the immediate charging procedure will
indicated in the "Alternating current
pressing button (A) fig. 213 on the port.
begin. LED (B) fig. 213 and LEDs (B)
(AC) charging at home", "Fast home
fig. 212 will light up green flashing/fixed
charging procedure from wallbox
depending on the state of charge of the
WARNING the button (A) fig. 213 on
charging station", "Charging procedure
battery portion indicated by the LED.
the port remains active for 1 minute
from public charging station (AC)"
The fixed green light indicates that the
after the doors are locked.
battery portion is fully charged.
208
To switch to immediate charging mode
DISCONNECTING THE
located next to the charging port will
during scheduled charging:
CHARGING CABLE
light up flashing red.
if charging is in progress, interrupt
The charging cable is locked during
the scheduled charging first (see
charging or when the doors are locked.
chapter "Interrupting charging");
To disconnect the charging cable,
activate immediate recharging by
interrupt the charging in progress (see
pressing the button again (A) fig. 213
the "Interrupting charging" paragraph).
on the port.
If no charging is in progress, first
unlock the doors using the button
Interrupting charging
on the key and then disconnect the
The charging cable is blocked when
charging cable.
charging is in progress. To interrupt the
charging process, unlock the doors
COMPLETION OF
215
F0S1209
with the key and press the button (A)
CHARGE
fig. 213 on the port. The charging
The full charging procedure, if not
"eCoasting" mode
process will be interrupted and you can
interrupted, ends when all LEDs (A)
(ENERGY SAVING)
disconnect the charging cable. When
fig. 214 they light up with a steady
This is a mode that replaces the
immediate recharging is interrupted
green light.
exhaust brake when the accelerator
and there is no charging scheduled
pedal is released, recovers energy
(see the "Charging schedule" chapter),
during the slowing down phase of the
the LEDs (B) fig. 212 will light up with a
car.
steady green light showing the current
The "eCoasting" mode is automatically
battery charge level; if there are any
activated in "NORMAL" operating
upcoming charging schedules, the
mode to maximise energy recovery
LEDs (B) fig. 212 will glow blue light
when the accelerator and brake pedals
and the LED will light up (A) fig. 212.
are released.
If a charging interval is interrupted, the
Driving in "eCoasting" mode is possible
same interval can only be resumed by
214
F0S1178
if the transmission is in position "D"
disconnecting and reconnecting the
(Drive).
charging cable, otherwise charging will
FAILURE DURING
continue with subsequent schedule.
CHARGING PROCEDURE
If a fault is detected during the charging
procedure first and last LED (A) fig. 215
209
"eBraking"
ONE-PEDAL
problem to the propulsion system.
To resume driving, press the
MODE (HIGH-
DRIVING
accelerator pedal and the electric
VOLTAGE BATTERY
With One-Pedal Driving in "RANGE"
parking brake will automatically release.
CHARGING)
and "SHERPA" modes, the accelerator
The One-Pedal Driving mode may
pedal can also be used to control
The "eBraking" mode, which is
shift the transmission to P if the car is
deceleration of the car to a complete
always active regardless of the
pushed after stopping or if there is a
stop.
problem with the electric motor.
selected operating mode activates the
Quickly release the accelerator pedal to
high-voltage battery charging when
TOWING TRAILERS
obtain aggressive deceleration. Slowly
the brake pedal is pressed, thereby
release the accelerator pedal to adjust
The vehicle is type-approved for
recovering energy during braking.
of the deceleration of the car.
towing. It is not permitted to mount an
The electric motor works as an
alternator, converting the kinetic energy
aftermarket towing device.
of the car into electrical energy.
WARNING When One-Pedal Driving
Using this mode is particularly useful
is active and the driver releases the
WARNING The installation of a towing
seat belt, the electric parking brake is
when driving in the city, where there
device on the vehicle can lead to
are continuous stops and starts.
applied automatically and One-Pedal
accidents and result in serious injury.
Driving is not possible.
NOTE To make the most efficient use
of the system, the braking phase
WARNING Never equip the vehicle
should, where possible, be modulated
Press the accelerator pedal to reach
with a towing device. Attaching towing
by applying so as to allow maximum
the desired speed. The deceleration
devices can cause extensive damage
energy recovery.
provided by One-Pedal Driving mode
to the vehicle.
NOTE In the event of an emergency,
allows for full regenerative braking and
maximum braking efficiency is always
helps to increase the efficiency of the
guaranteed by the conventional braking
car.
system.
With the One-Pedal Driving mode
enabled, the electric parking brake may
be automatically applied if:
the car stops on a slope;
the driver’s door is open;
car stopped for longer than five
minutes;
210
IN AN EMERGENCY
Have a flat tyre or a burnt-out bulb?
HAZARD WARNING LIGHTS
212
At times, a problem such as these may
ASSIST CALL
212
interfere with your driving experience.
EMERGENCY CALL - EU eCall
214
The pages on emergencies can help
IN CASE OF ACCIDENT
218
you to deal with critical situations
REPLACING A BULB
219
independently and calmly.
FUSES
224
In an emergency, we recommend that
FIX&GO KIT
225
you call the phone number found in the
Warranty Booklet.
JUMP STARTING
230
It is also possible to call the national
TOWING THE CAR
230
or international universal freephone
number to search for the nearest
Dealership.
211
HAZARD WARNING
ASSIST CALL
LIGHTS
The car is equipped with an on-board
Press button (A) fig. 216 to switch the
assistance function designed to provide
hazard lights on/off regardless of the
support in the event of malfunctions of
A
position of the ignition device. With the
the car.
The ASSIST function is activated:
device on, warning lights and light
up in the instrument panel. Press the
automatically (where provided)
button (A) again to switch the lights off.
following malfunctions of the braking
system system, motor, etc.
218
F0S1382
manually, by pressing the ASSIST
button (B) fig. 217 (where provided)
The ASSIST function is activated with:
located on the ceiling light or via the
ignition device in the ENGINE
"Assist" app (A) fig. 218 present on the
position;
Uconnect™ system (where provided).
ignition device in STOP position and
For more information, refer to the
Uconnect™ system display on.
"Apps" paragraph in the "Uconnect™"
Once activated automatically (where
chapter of the "Multimedia" section.
provided) or manually by pressing the
216
F0S1159
corresponding button, the EU eCall
function will send the position data of
WARNING The use of hazard warning
the car to the Operations Centre and
lights is governed by the highway
stablish a voice call with an operator.
code of the country you are driving in:
NOTE If the ASSIST function does
comply with legal requirements.
work, the fault in the system will be
indicated on the display. Go as soon
as possible to a Fiat Dealership to have
Emergency braking
the function repaired.
In the event of an emergency
217
F0S1160
NOTE The correct operation of the
braking, the hazard warning lights
ASSIST services will be guaranteed
switch on automatically together
only by a good network coverage.
with warning lights and on the
instrument panel. The lights switch off
automatically when emergency braking
WARNING The ASSIST function may
ceases.
not be available for the first minute after
the car is started.
212
The "ASSIST call" function is not
WARNING The icon at the top of
will turn off when the connection is
the emergency call, also known as
the Uconnect™ display indicates
ended.
"eCall", which is required by law in
that the geo-location function is
NOTE If the ASSIST call button is
the countries of the European Union
active (ON). When geo-location is on,
pressed by mistake, the call can be
(EU eCall) based on the emergency
the car position is tracked to enable
ended by pressing the same button
number 112 and described in the "SOS
the functions that require it. When
again or by pressing the cancel button
Call" chapter in the "In an emergency"
geo-location is off, the car position
on the Uconnect™ system display.
section.
is only tracked by the navigation,
Once the connection has been
Privacy: for the ASSIST call service,
safety, insurance and driver assistance
established, the following data will
the location (GPS) of the car cannot be
systems (where provided). This
be automatically transmitted, as
deactivated because it is indispensable
function can be deactivated using the
authorised by the customer:
for the provision of the service itself.
Uconnect™ system (see "Settings" in
indication that the occupant has
The localisation for this service cannot
the"Vehicle mode" paragraph in the
made an ASSIST call;
be deactivated even with "Privacy
"Multimedia" section).
the brand of the car;
Mode" activated ("Geo-location
the most recent known GPS
OFF"). Furthermore, deactivating the
coordinates of the car;
Pressing the ASSIST button (where
positioning of the car by means of the
the type of error that occurred in the
provided) located on the front ceiling
"Settings" menu of the Uconnect™
car that automatically sent the ASSIST
light (B) fig. 217 and/or on the display
system will make other services
request (in the case of an automatic
fig. 218 of the Uconnect™ system
(other than the one described here)
call - where provided).
(where provided) to call to one or more
unavailable (for more details see
The call will be made through the car
of the following services:
"Settings" chapter of the Uconnect™
sound system to provide any additional
Roadside assistance: if case of
system).
information about the assistance
need, a connection will be established
FCA Italy S.p.A. processes personal
request.
with the roadside assistance authority
data ("Data") - as the Data Controller
If the system is unable to establish the
which will receive the car type and its
- in accordance with the provisions of
voice call, or the line disconnects due
position directly. Additional roadside
Italian Legislative Decree 196/2003 as
to insufficient coverage, the ASSIST
assistance charges may apply.
amended by Italian Legislative Decree
service will try to call the Operations
Customer care (where provided):
101/2018, Regulation (EU) 2016/679
Centre again for certain number of
Customer service to support all car
and any other personal data protection
times.
problems.
regulations in force. In this regard,
The LED on the ASSIST button located
refer to the Privacy Policy on the Patto
on the ceiling light will turn green once
WARNING If you have not subscribed
Chiaro Vendita.
connected to an ASSIST operator and
to the related services or the My
Assistant package has expired or is
213
unavailable for purchase, the ASSIST
could affect or entirely prevent service
call will not be available. For further
operation.
information visit the Fiat official website.
NOTE Regardless of state of charge,
the battery must be replaced every 5
WARNING If the ASSIST call system
years by a Fiat dealership.
detects a malfunction, it is indicated
EMERGENCY CALL -
by the red LEDs on the ceiling light
EU eCall
and a corresponding message on the
Uconnect™ system display. Contact a
The car is equipped with an on-board
Fiat Dealership as soon as possible.
assistance function designed to provide
219
F0S1198
support in the event of accident and/or
If a EU eCall is active and an ASSIST
emergency (SOS). The emergency
The EU eCall function is activated with:
call, also known as "eCall", which is
ignition device in the ENGINE
call is requested, the latter will not be
required by law in the countries of
position;
delivered.
the European Union (EU eCall) based
ignition device in the STOP position.
Uconnect Box SYSTEM
on the emergency number 112, can
In the STOP position, the EU eCall
BATTERY
be used to call for help quickly in
is available for 10 minutes after the
The Uconnect Box system is provided
dangerous situations.
ignition device is switched from
with an independent battery that allows
The EU eCall emergency call activates
ENGINE to STOP.
the operation of some connected
the voice call to the Operations
This condition is only valid for cars
services even if the 12V battery of the
Centre dedicated to emergency calls
equipped with SOS call in accordance
car is disconnected.
(112) with simultaneous activation of
with the legal regulations in the
The system will warn the user of
the transmission of the car data and
countries where it applies.
the need to replace this battery by
geo-location. The EU eCall service is a
Once activated automatically (where
displaying a dedicated message on the
public service of general interest and
provided) or manually by pressing the
display of the Uconnect™ system
free of charge.
SOS button, the EU eCall function will
(where provided) and by means of
The EU eCall function can be activated:
send the position data of the car to the
a notification via mobile app (where
Automatically, in the event of a major
Operations Centre, such as geolocation
provided).
collision recorded by the device by
of the car, and establish a voice call
Go to a Fiat dealership as soon as
with an operator.
means of the presence of sensors
possible.
aboard the car.
NOTE If the EU eCall function does
NOTE Failure to replace the battery
Manually, holding the SOS button
not work, the fault in the system will
and, consequently, failure to observe
(A) located on the ceiling light fig. 219
be indicated on the instrument panel
the warnings provided by the system
pressed (for longer than 2 seconds).
display. Go as soon as possible to a
214
Fiat Dealership to have the function
AUTOMATIC EMERGENCY
Centre responsible for emergency calls
repaired.
CALL
(number 112).
NOTE The correct operation of the EU
The automatic emergency call system
The green light will go out when the call
eCall function will be guaranteed only
is only available if the car is in READY
is interrupted.
by a good network coverage.
ON status ("READY" symbol on
Interrupting a call
Privacy: the location (GPS) of the car
instrument panel).
If the SOS call button is pressed by
can never be deactivated because
The system makes an automatic
mistake, it is possible to press it again
it is indispensable for the eCall
emergency call if certain conditions are
within 10 seconds to cancel the
service. Furthermore, deactivating
met, e.g. an airbag is deployed.
operation. After 10 seconds, only the
the positioning of the car, performed
The flashing green light located on the
operator of the Operations Centre can
by activating "Privacy Mode" ("Geo-
SOS button (A) fig. 219 on the front
interrupt the call.
location OFF") in the "Settings" menu
ceiling light will indicate that the system
If you are able to speak to the operator,
items of the Uconnect™ system will
is trying to make the emergency call.
do so through the car audio to provide
make other services - other than the
The fixed green light will indicate that
additional information about the
one described here - unavailable
the call has been established.
request for help.
(for more details see "Settings" in
Interrupting the call
If the system is unable to establish
the"vehicle mode" paragraph in the
The automatic emergency call cannot
the voice call, or the line disconnects
"Multimedia" section).
be interrupted by the user but will only
due to insufficient coverage, EU eCall
be interrupted by the operator of the
service will try to call the Operations
WARNING The icon at the top of
Emergency Operations Centre.
Centre again for 5 minutes.
the Uconnect™ display indicates
If the Operations Centre needs to
that the geo-location function is
MANUAL EMERGENCY
contact the car again, the system can
active (ON). When geolocation is on,
CALL
receive, for up to 120 minutes from the
the car position is tracked to enable
To make the emergency call manually
ending of the call with the operator, an
the functions that require it. When
make sure that the instrument panel is
incoming call, which will be accepted
geolocation is off, the car position
on ("READY" symbol on the instrument
automatically. Until the end of 120
is only tracked by the navigation,
panel).
minutes, the system will be completely
safety, insurance and driver assistance
Press the SOS call button on the front
dedicated to the management of the
systems (where provided). To
ceiling light for about 2 seconds (A)
emergency in progress, therefore it will
deactivate this function, see "Settings"
fig. 219.
not be able to provide any connectivity
in the "Vehicle mode" paragraph in the
The green light located at the SOS
service.
"Multimedia" section).
button will flash and then become fixed
once the connection has been made
with an operator of the Operations
215
LED signalling / colours
Go to a Fiat dealership as soon as
Data processing is carried out in
Green light
possible.
accordance with current European
In flashing mode: this indicates that
NOTE Failure to replace the battery
legislation (EU Regulation 2016/679
the emergency call has been activated,
and, consequently, failure to observe
also known as "GDPR").
whether it was made manually or
the warnings provided by the system
When the call is connected, the
automatically.
could affect or entirely prevent service
following data will be automatically
In fixed mode: this indicates that
operation.
transmitted to the Operations Centre:
contact has been established with
NOTE Regardless of state of charge,
Identification of the data packet sent.
the Emergency Operations Centre
the battery must be replaced every 5
(The operator may request an updated
operator.
years by a Fiat dealership.
data package during the call)
Off: this indicates that the
car Identification Number
EU eCall SYSTEM
emergency call has ended.
Type of traction (electric, petrol,
FAULTS
Red light
Diesel, LPG, etc.)
If the EU eCall system detects a
This indicates a fault in the EU eCall
Date, time and minute when the call
malfunction, this is indicated by the red
system with the impossibility to make
was made
light on the ceiling light and a dedicated
an emergency call or with the possibility
Call type: Manual (via SOS button) or
icon on the instrument panel display.
to do so with limitations. Go to a Fiat
Automatic (following a collision)
Through this icon, the system will
dealership as soon as possible when
Vehicle type (car or van)
recommend having the battery
this light is red.
Type of traction (electric, petrol,
checked if it has a low level of charge
Diesel, LPG, etc.)
Uconnect Box SYSTEM
or a malfunction, and will provide
Reliability of the sent position
BATTERY
information about the current system
(depending on the condition of the GPS
The Uconnect Box system is provided
update and call status (in progress,
signal at the time of the call)
with an independent battery that allows
failed, etc.).
Location relative to the time of the
the operation of some connected
If a fault is present, contact a Fiat
call. If the call is made from a location
services even if the 12V battery of the
Dealership as soon as possible.
where the GPS position is available, the
car is disconnected.
Privacy - Information on
position of the car will be sent at the
The system will warn the user of
personal data ("Data")
start of the call; if the GPS signal is not
the need to replace this battery by
processing
available, e.g. inside a tunnel, the last
displaying a dedicated message on the
available position will be sent
The geolocation (GPS) function of the
display of the Uconnect™ system
car is always active and can never be
Two positions before the main
(where provided) and by means of
deactivated for the EU eCall service,
position sent and the direction of travel
a notification via mobile app (where
of the car.
even when the "Privacy Mode" system
provided).
is activated ("Geolocation OFF").
216
Data processing is strictly limited to the
Italy S.p.A. shall retain the geolocation
1. right of access, i.e. the right to
sole purpose of making emergency
data relating to the position of the
obtain confirmation from FCA whether
calls to 112, the single European
VEHICLE - recorded at the time of
or not the Data are being processed
emergency number.
the accident - for the period deemed
and, if so, to obtain access to them;
The recipients of the Data processed
strictly necessary to provide this
2. right of correction and erasure, i.e.
through EU eCall are the emergency
Service. In addition, the Data may be
the right to obtain the correction of
call collection centres that are the
retained by FCA for a longer period
inaccurate Data and/or the integration
first designated by the competent
to deal with any disputes related to
of incomplete Data or the deletion of
Authorities of the country in whose
the provision of the Service and to
Data for legitimate reasons;
territory the vehicle is located to receive
ascertain, exercise or defend the rights
3. right to the restriction of processing,
and process eCalls to the single
of FCA in judicial and/or extrajudicial
i.e. the right to request the suspension
European emergency number 112.
proceedings. After this period, the
of processing where legitimate reasons
The EU eCall system is designed to
Data will either be anonymised or
exist;
permanently erased.
ensure that the Data in the system
4. right to data portability, i.e. the right
memory is not available outside the
The Data Controller of the aforesaid
to receive the Data in a structured,
system before an eCall is activated.
personal data is FCA Italy S.p.A.
commonly used and readable format,
The EU eCall system, in normal
(hereinafter "FCA") with registered office
as well as the right to transmit the Data
operation, is not traceable and
in Corso Agnelli 200, 10135 Torino,
to another data controller;
cannot be monitored at all times. It
Italy.
5. right to object, i.e. the right to
ensures that data is automatically and
The data subjects can contact the Data
object to the processing of Data if
continuously erased from the internal
Protection Officer's team at the email
there are legitimate reasons, including
memory of the system.
address dpo@fcagroup.com.
processing of Data for marketing and
The car geolocation data car are
FCA undertakes to comply with the
profiling purposes, if any;
constantly overwritten in the internal
applicable laws on Data Protection and
6. right to contact the competent data
memory of the system to store at most
in particular with the requirements
protection authority in case of unlawful
the last three positions of the car,
of Legislative Decree No. 196/2003
processing of Data.
necessary for the normal operation of
as amended by Italian Legislative
The data subject may exercise the
the system.
Decree 101/2018 and of EU Regulation
rights listed above by writing to FCA
The data protocol of the EU eCall
2016/679.
Italy S.p.A., Corso Giovanni Agnelli 200
system activities is kept only for the
Refer to the Privacy Policy on the Patto
10135 Torino Italy or to the following
time necessary to manage the eCall
Chiaro Vendita.
email address: privacy@fcagroup.com:
emergency call and in any case for no
The following rights are granted to the
Furthermore, the data subject has the
more than 13 hours from the time the
data subject:
right to lodge a complaint with the
eCall emergency call was initiated. FCA
competent Data Protection Authority
217
if he or she considers that his or her
IN CASE OF
blindness or skin lesions may occur.
rights have been violated as a result of
Any vapors released from the
ACCIDENT
the processing of his or her personal
electrolyte, if inhaled, may also cause a
data.
217)
risk of intoxication. In case of contact
with the electrolyte, rinse immediately
WARNINGS
AUTOMATIC HIGH-
with plenty of water and seek medical
In the event of danger (fire, visible
VOLTAGE BATTERY
attention;
smoke or hazardous road conditions
DISCONNECTION
do not go near the high-voltage
or dangerous positions), do not wait
In the case of an accident, with the
battery with naked flames: danger of
for voice contact with the Emergency
intervention of the battery disconnect
FIRE. In case of fire, do not use water
service operator, but exit from the car
system and airbags, the high-voltage
extinguishers to extinguish the fire; the
immediately and go to a safe place, if in
battery is disconnected automatically,
use of water, even in small quantities,
a condition to do so.
to avoid possible fire risks that could
can be dangerous;
Do not place network CB radios or
put passengers and any other people
if the car has been seriously
aftermarket electrical equipment to
involved in traffic and/or near the car in
damaged, maintain a safe distance of
avoid interference. Such interference
a dangerous condition.
at least 15 metres between the car and
could prevent the system form making
To reactivate the high-voltage battery,
the other cars / flammable materials.
the emergency call.
contact a Fiat Dealership.
Ignoring system fault signals (red LED
PRECAUTIONS IN CASE
on the ceiling light and dedicated
OF ACCIDENT
WARNING
messages on the instrument panel)
To minimise the risk of serious injury,
may mean that you cannot make an EU
observe the following precautions:
217) Do not touch high-voltage
eCall, if necessary.
park safely on the side of the road,
components (identified by the colour
Even if the EU eCall system is fully
orange) or any components that have
apply the electric parking brake, put
functional, factors outside the
come into contact with exposed
the one-speed transmission in P and
high-voltage cables. NEVER touch
control of FCA could interfere with or
switch off the electric motor;
exposed electric cables: danger of
prevent operation of the EU eCall.
contact rescue immediately, warning
ELECTROCUTION.
These factors can be identified in:
that it is a electric car equipped with a
clogged or unavailable satellite signals,
high-voltage system;
network connection, adverse weather
if you notice any electrolyte leakage
conditions, buildings, interfering
from the high-voltage battery, do not
structures, tunnels, etc.
go near the vehicle. If the electrolyte
from the high-voltage battery comes
into contact with the eyes or skin,
218
REPLACING A BULB
218) 219) 220)
82) 83)
GENERAL
INSTRUCTIONS
Before replacing a bulb check the
contacts for oxidation;
burnt bulbs must be replaced by
others of the same type and power;
always check the headlight beam
direction after changing a bulb for
safety reasons;
when a light is not working, check
that the corresponding fuse is intact
before replacing a bulb. For the
location of fuses, refer to the "Fuses
replacement" chapter in this section.
WARNING When the weather is cold or
damp or after heavy rain or washing,
the surface of headlights or rear lights
may steam up and/or form drops of
condensation on the inside. This
is a natural phenomenon due to the
difference in temperature and humidity
between the inside and the outside
of the glass which does not indicate
a fault and does not compromise the
normal operation of lighting devices.
The mist disappears quickly when
the lights are turned on, starting from
the centre of the air vent, extending
progressively towards the edges.
219
BULB TYPES
The car is equipped with the following bulbs:
All-glass bulb: (type A) these are pressure fitted - pull to remove.
A
Bayonet bulb: (type B) to remove them press the bulb and turn it anticlockwise.
B
Cylindrical bulbs: (type C) release them from their contacts to remove.
C
Halogen bulbs: (type D) release the fastening clip from its housing to remove
D
the bulb.
220
Light bulbs
Use
Type
Power
Ref. Figure
H19 (where provided)
Dipped/Main beam headlights
55/60W (where provided)
D (where provided)
(LED) (where provided)
(LED) (where provided)
Front side lights/Daytime running lights (DRL)
5W (where provided)
A (Where provided)
W5W (where provided)
PSY24 (where provided)
Front direction indicators
24W (where provided)
B (where provided)
(LED) (where provided)
Side direction indicators
LED
-
-
Rear direction indicators
LED
-
-
Tail/brake light
LED
-
-
Reverse gear
W16W
16W
B
Rear fog light
W16W
16W
B
Ceiling light
C5W
5W
C
Boot light
W5W
5W
A
Number plate light
LED
-
-
Third brake lights
LED
-
-
221
REPLACING AN
EXTERNAL BULB
FRONT LIGHT CLUSTERS
The front light clusters contain side/tail
lights, dipped headlights, main beam
headlights and direction indicator
bulbs.
LED front direction indicators
For replacement, contact a Fiat
220
F0S1161
221
F0S1162
Dealership.
Side direction indicators
remove the pressure-fitted bulb and
remove the bulb holder by pressing
The side direction indicators of the LED
replace it;
the fins (B) fig. 222;
type. For replacement, contact a Fiat
refit the bulb holder locking it
remove the pressure-fitted bulb and
Dealership.
correctly;
replace it;
refit the rubber cap.
refit the bulb holder locking it
Dipped/main beam headlights
correctly.
Contact a Fiat Dealership for replacing
Side/tail lights/daytime running
an LED dipped beam/main beam
lights (DRL)
headlight. If the car is fitted with dipped
The side lights/daytime running
beam/main beam headlights of the
lights (DRL) are of the LED-type. For
light bulb type, proceed as follows to
replacement, contact a Fiat Dealership.
replace them:
Front direction indicators
operating from the motor
Contact a Fiat Dealership for replacing
compartment remove the protective
a front direction indicator of the LED
rubber cap (A) fig. 220;
type.
press the fastener and remove the
If the car is fitted with direction
bulb holder;
222
F0S1163
indicators of the light bulb type,
proceed as follows to replace them:
REAR LIGHT CLUSTERS
remove the wheel arch (A) fig. 221 by
These contain the functions of the
undo the appropriate screws;
tail lights, brake lights and direction
indicators. The reversing lights and rear
fog lights are located instead in the rear
bumper.
222
The tail, brake, third brake lights and
the direction indications are of the LED
type. For replacement, contact a Fiat
Dealership.
REVERSING LIGHT/REAR FOG
LIGHT
To replace the reversing and rear fog
light, access the bulb holder through
the lower part of the rear bumper
fig. 223.
224
F0S1165
225
F0S1166
refit the bulb/bulb holder (A) by
turning it clockwise.
THIRD BRAKE LIGHTS
The third brake lights are LED-type. For
replacement, contact a Fiat Dealership.
NUMBER PLATE LIGHTS
The number plate lights are LED-type.
For replacement, contact a Fiat
223
F0S1164
Dealership.
226
F0S1313
rotate the bulb holder (A) fig. 224
REPLACING INTERIOR
remove the lens assembly and
anticlockwise and extract it. Undo
BULBS
replace the press-fit bulb (A) fig. 226,
the outer bulb holders to replace the
Inside ceiling light
making sure that it locks correctly.
reversing lights. Undo the central bulb
To replace the bulbs, proceed as
holder to replace the rear fog light;
follows:
Boot light
release the bulb and replace it;
operate in the points indicated by
(where provided)
the arrows and remove ceiling light (A)
To replace the bulb, proceed as
fig. 225 complete with its frame;
follows:
open the boot;
using the screwdriver, extract the
ceiling light (A) fig. 227 working in the
point shown by the arrow;
223
FUSES
WARNING
221) 222)
84)
218) Modifications or repairs to the electric
system that are not carried out properly
or do not take the system technical
WARNING
specifications into account can cause
malfunctions leading to the risk of fire.
219) Halogen bulbs contain pressurised
221) Replacement of a fuse. All
gas, in the case of breakage they may
work may be performed only by a Fiat
burst causing glass fragments to be
Dealership or a qualified repair workshop.
227
F0S1323
projected outwards.
The replacement of a fuse by a third party
220) Only replace the light bulbs when the
may cause a serious car fault.
open the protection (B) fig. 228
motor is off and in a position that does
222) Installation of electrical
replace the snap-fitted bulb;
not interfere with traffic and lets you safely
accessories. The car’s electrical circuit
replace them (see the description in the
is designed to function with standard or
“When parked" chapter in the "Starting
optional equipment, before installing other
and driving" section). Also ensure that the
electrical equipment or accessories in the
motor is cold, to prevent the risk of burns.
vehicle contact a Fiat dealership or a
qualified repair workshop.
IMPORTANT
IMPORTANT
82) Halogen bulbs must be handled
holding the metallic part only. Touching
84) FCA shall not be held liable for
the transparent part of the bulb with your
expenses resulting from car repair or
fingers may reduce the intensity of the
anomalies resulting from the installation
228
F0S1324
emitted light and even reduce the lifespan
of accessories not provided or
of the bulb. In the event of accidental
recommended by Fiat and not installed
close the cover (B) on the lens;
contact, wipe the bulb with a cloth
according to specifications, in particular
then refit the ceiling light by inserting
moistened with alcohol and let the bulb
when the combined consumption of all
it correctly in its housing, on one side
dry.
additional equipment connected exceeds
and then pressing on the other side
83) Where possible, it is advisable to have
10 mA.
until it clicks into place.
bulbs changed at a Fiat Dealership. The
correct operation and direction of the
external lights are absolutely essential for
the safety of the car and of compliance
with the law.
224
FIX&GO KIT
event of a puncture, change the tyre
Repair procedure
in accordance with the laws of the
Proceed as follows:
(where provided)
country in which you are travelling.
insert the sealant cartridge (A)
223) 224) 225) 226) 227) 228) 229) 230)
into the corresponding compressor
OPT1 KIT DESCRIPTION
85) 86)
compartment (B) and press it down
231)
6)
hard. Remove the speed limit sticker
The Fix&Go is located in the boot inside
The car may be equipped with a
(C) and apply it in a clearly visible
its own box.
different Fix&Go (Kit OPT1 or Kit OPT2)
position;
To access the Fix&Go open the
according to the version.
wear the gloves;
luggage compartment tailgate and lift
remove the cap from the tyre valve
Preliminary operations
the load floor.
and connect and screw the transparent
Proceed as follows:
The Fix&Go fig. 229 includes:
tube of the sealing fluid (D) onto the
stop the car in a position that is not
one cartridge (A) containing sealant
valve.
dangerous for oncoming traffic where
and fitted with: transparent tube for
If a 250 ml cartridge is present the
you can change the wheel safely. The
injecting the sealant (D) and sticker (C)
housing of the transparent tube is
car must be stopped in a lay-by, car-
with the wording MAX. 80 km/h / 50
provided with a removable ring to
park or parking or service area, and the
mph to be applied in a clearly visible
facilitate extraction
ground must be as level as possible
position (e.g. on the dashboard) after
make sure that the ON/ OFF button
and sufficiently compact;
repairing the tyre;
(E) fig. 231 is in the off position (button
turn the ignition device to the OFF
one compressor (B);
not pressed);
position, apply the electric parking
a pair of gloves located in the hose
brake and shift the gear to position P or
compartment of the cartridge (D).
R;
steer the wheels completely;
D
C
in the event of a steep slope, place a
A
wedge or stone behind the wheels;
before getting out of the car, put on
C
the reflective safety jacket (if required
by the regulations in force). In any case,
follow the road safety laws in force in
the country where you are driving;
230
F0S1294
make sure that any passengers get
B
out of the car and go to a safe place
insert the electrical connector (C)
229
F0S1246
where they will not obstruct traffic or
fig. 230 in the 12 V power socket of the
be exposed to the risk of injury. In the
car and start the engine;
225
operate the compressor by pressing
compressor and restore pressure using
the ON/OFF button (E) fig. 231. When
the black inflation tube (I).
the pressure gauge (G) reaches the
A
recommended pressure (see the
“Wheels” chapter in the “Technical
ON
Data” section) or the pressure
indicated on the specific label) stop the
compressor by pressing the ON-OFF
button again;
H
disconnect the cartridge (A) fig. 232
232
F0S1263
I
from the compressor, by pressing
the release button (H) and lifting the
If the pressure gauge (G) fig. 231
233
F0S1264
cartridge upwards.
indicates a pressure lower than 1.8
bar (26 psi) 15 minutes after starting
G
the compressor, switch off the
compressor, disconnect the sealing
fluid tube (D) fig. 229 from the tyre valve
and remove the cartridge (A) from the
compressor.
E
A
L
Move the car by approximately 10
metres to allow the distribution of
the sealant. Stop the vehicle safely,
231
F0S1262
operate the electric parking brake
234
F0S1293
and restore pressure using the black
inflation pipe (I) fig. 233 to reach the
If the pressure shown is higher than
required pressure. If also in this case,
1.8 bar / 26 psi, restore the pressure
the pressure is lower than 1.8 bar
and drive safely to a Fiat Dealership
/ 26 psi 15 minutes after turning on,
as soon as possible. If, however, the
do not resume driving but contact a
pressure is lower than 1.8 bar / 26 psi,
Fiat Dealership. After driving for about
do not resume driving but contact a
8 km / 5 miles fig. 234, move the car to
Fiat Dealership.
a safe and suitable area and engage
232)
the electric parking brake. Take the
226
Inflation procedure
OPT2 KIT DESCRIPTION
Proceed as follows:
233) 234) 235)
stop the car safely, as described
above, and operate the electric parking
brake;
extract the black inflation tube and
screw it firmly onto the tyre valve. Then
follow the instructions below. Press
the air release button to adjust any
excessive tyre pressure (see "Repair
237
F0S0824
procedure" paragraph).
Cartridge replacement
(G) Cap for the sealant bottle
Proceed as follows:
235
F0S0822
(H) Sealant bottle and expiry date
only use original cartridges, which
(I) Speed label
can be purchased from the Fiat
(A) Pressure gauge
Dealership;
(B) Instruction label
Description
to remove the cartridge, press the
(C) On/Off switch
release button and lift it (see description
above).
238
F0S0825
236
F0S0823
The quick tyre repair kit fig. 238 is
located in the boot or in the toolbox
(D) Air pipe
and consists of a compressor (B) and
(E) Deflation button
a cartridge containing sealing fluid (A)
(F) Power supply cable / 12V plug
and an adhesive sticker (C) with the
wording "Max km 80Km/h", which is to
be placed in a clearly visible position
227
(e.g. instrument panel) after the tyre
remove the cap from the tyre valve
when the pressure gauge indicates
repair.
and screw the black compressor tube
the prescribed pressure indicated in
onto the valve
the "Wheels” chapter, "Technical Data”
Repair procedure
make sure that the ON/OFF button is
section or on the label, switch the
in the off position (button in position 0)
compressor off by turning the button to
the OFF position (0)
239
F0S0826
Proceed as follows:
241
F0S0835
take the kit, detach the speed limit
243
F0S0837
sticker (I) fig. 237 and apply it in a
insert the electrical connector
clearly visible position fig. 239
fig. 241 into the 12V socket on the car
If the pressure gauge fig. 243 indicates
a pressure lower than 2 bar / 29 psi 10
minutes after starting the compressor,
switch off the compressor, disconnect
the black tube of the compressor from
the tyre valve and undo the cartridge
from the compressor turning it by one
quarter of a turn anticlockwise and lift
it. Move the car by approximately 10
metres to allow the distribution of the
sealant.
240
F0S0834
242
F0S0836
Stop the engine, switch on the hazard
lights; stop the vehicle safely, apply the
open the cap on the compressor,
activate the compressor setting the
parking brake; engage 1st gear if uphill
engage the cartridge and turn a quarter
ON-OFF button, fig. 242, to the on
or reverse gear if downhill; wheels all
turn clockwise, fig. 240
position (button in position I)
steered; on a steep gradient, place a
228
wedge or stone behind the wheels
as soon as possible. If, however, the
call roadside assistance. Do not remove
and restore pressure using the black
pressure is lower than 2 bar / 29 psi,
foreign bodies from the tyre.
compressor tube fig. 242 until the
do not resume driving but contact a
224) Punctures on the sides of the tyre
may not be repaired. Do not use the
prescribed pressure is reached.
Fiat Dealership.
Fix&Go if the tyre was damaged as a result
If also in this case the pressure is lower
Pressure relief valve
of being used with the wheel underinflated.
than 2 bar / 29 psi 10 minutes after
225) Wear the protective gloves provided
turning on, do not resume driving and
with the Fix&Go.
contact a Fiat Dealership.
226) Apply the adhesive label where it can
be easily seen by the driver as a reminder
that the tyre has been treated with the
Fix&Go. Drive carefully, particularly on
bends.
227) Repairs are not possible in the case
of damage to the wheel rim (bad groove
distortion causing air loss). Do not remove
the foreign body (screws or nails) from the
tyre.
245
F0S0839
228) As required by current regulations,
the information on chemical substances
If the tyre pressure is higher than
for the protection of human health and the
expected, after switching off the
environment and on the safe use of the
244
F0S0838
compressor, it can be lowered by
sealing fluid are on the packaging label.
Compliance with the indications on the
After driving approximately 8 km / 5
means of the button, fig. 245, located
label is an essential condition to ensure
miles, place the vehicle in a safe and
next to the black tube connection.
the safety and the effectiveness of the
easy area, stop the engine, switch on
product. Remember to carefully read the
the hazard lights, apply the parking
label before use; the user of the product
is responsible for any damages caused
brake; engage 1st gear if uphill or
WARNING
by improper use. The sealing fluid has an
reverse gear if downhill with wheels all
expiration date. Replace the bottle if the
steered. In the event of a steep slope,
223) IMPORTANT: Do not exceed
sealant has expired.
place a wedge or stone behind the
80 km/h. Avoid sudden acceleration or
229) The Fix&Go kit is not suitable for
wheels.
braking. The kit provides a temporary
definitive repairs, so the repaired tyres may
repair, therefore the tyre must be
only be used temporarily. The Fix&Go kit
Take the compressor and restore the
examined and repaired by a specialist
provides a temporary repair, therefore the
pressure using the black inflation tube.
as soon as possible. Before using the
tyre must be examined and repaired by a
If the pressure shown is higher than
kit, ensure that the tyre isn't excessively
specialist as soon as possible.
2 bar / 29 psi, restore the pressure
damaged and that the rim is in good
230) Alert other drivers that the car
condition, otherwise do not use it and
is stationary in compliance with local
and drive safely to a Fiat Dealership
229
regulations: hazard warning lights, warning
and putting the transmission in position
IMPORTANT
triangle, etc. Any passengers on board
N.
should leave the car, especially if it is
BUMP STARTING
heavily laden. Passengers should stay
6) Dispose of the bottle and the sealant
away from on-coming traffic while the
liquid properly. Have them disposed of
Never bump start the motor by
wheel is being changed. On hills or uneven
in compliance with national and local
pushing, towing or driving downhill.
roads, use chocks or appropriate objects
regulations.
to block the wheels of the vehicle.
231) Never operate the compressor for
WARNING Remember that the brake
longer than 20 consecutive minutes: risk of
JUMP STARTING
servo and electric power steering
overheating.
system (where provided) are not active
232) If the pressure falls below 1.8 bar, do
Jump starting using cables and/or
until the ignition device is in ENGINE
not drive any further: the Fix&Go cannot
using an auxiliary 12V battery is never
position. A much greater effort will
guarantee proper seal because the tyre is
permitted. Risk of damaging the
too damaged. Contact a Fiat Dealership.
therefore be required to use the brake
electrical system of the car. Contact a
233) Carefully read the cartridge label
pedal or turn the steering wheel.
Fiat Dealership.
before use and avoid improper use. The kit
should be used by adults and cannot be
STARTER WITH FLAT
TOWING THE CAR
used by children.
HIGH-VOLTAGE BATTERY
234) Do not let the compressor turned on
AND 12V BATTERY
236) 237) 238) 239) 240)
for longer than 10 consecutive minutes -
overheating hazard
Jump starting is not possible with
The tow ring provided with the car is
235) Use the kit only in case of a
a discharged high-voltage battery.
housed in the tool bag under the boot
punctured tyre.
Proceed as follows:
mat.
Contact a Fiat Dealership.
The car may not be towed. It can only
transport the car with a tow truck
be transported on a tow truck as
IMPORTANT
to a public or private charging point
shown in fig. 246.
and charge the high-voltage battery
85) The sealant fluid is effective with
external temperatures from -40°C to
(for transport see the "Towing the car"
+50°C. The sealant fluid has an expiry date
chapter in this section).
and must be replaced periodically. It is
possible to repair tyres with damage on
FLAT HIGH-VOLTAGE
the tread up to a maximum diameter of
BATTERY AND 12V
6 m m. Show the cartridge and the label
BATTERY
to the personnel who will handle the tyre
In this condition it is possible to move
treated with the Fix&Go.
the car for a few metres, positioning the
86) The surface of the tube may be hot.
ignition device to the ENGINE position
246
F0S1302
230
ATTACHING THE TOW
that the ring is fully fastened in the housing
HOOK
before towing the car.
Front
237) NEVER tow the car with two or four
wheels on the road. Risk of damaging the
Proceed as follows:
motor and fire hazard. It is imperative that
release the cap fig. 247;
the car is towed by a tow truck.
take the tow ring out of its housing in
238) In the case of a discharged high-
the tool support;
voltage battery and a discharged 12V
battery, NEVER tow the car. Transport
fully tighten it on the threaded pin.
it on a tow truck and contact a Fiat
Dealership.
239) It is permitted to tow for short
distances at a speed not exceeding 5
km/h using a special device conforming to
the Highway Code (rigid bar) and ONLY
for preparation for transport by tow truck,
keeping the broken-down car aligned on
the same centreline as the tow truck.
240) Tow rings MUST NOT be used to
tow cars off the road or where there are
obstacles and/or for towing operations
247
F0S1169
using cables or other non-rigid devices.
FLAT HIGH-VOLTAGE
BATTERY AND 12V
BATTERY
In this condition it is possible to move
the car for a few metres, positioning the
ignition device to the ENGINE position
and putting the transmission in position
N.
WARNING
236) Before tightening the ring clean the
threaded housing thoroughly. Make sure
231
MAINTENANCE AND CARE
Proper maintenance allows car
SCHEDULED SERVICING
233
performance to be maintained over
CHECKING LEVELS
237
time, operating costs to be contained,
12V BATTERY
240
and safety system performance to be
RUBBER HOSES
241
safeguarded.
BRAKES
241
This section explains how.
REPLACING THE
WINDSCREEN/REAR WINDOW
WIPER BLADES
241
RAISING THE CAR
243
WHEELS AND TYRES
243
CAR INACTIVITY
244
BODYWORK
245
INTERIOR
248
232
SCHEDULED
SERVICING
Correct servicing is crucial for
guaranteeing a long life for the car
under the best conditions. For this
reason, Fiat has planned a series of
checks and services at fixed distance
and/or time intervals, as described in
the Service Schedule.
To keep the efficiency of the car in tip-
top condition, in the following Service
Schedule pages a few additional
checks are listed that should be carried
out more frequently with respect to the
normal scheduled service deadline.
Scheduled Servicing is offered by Fiat
Dealerships according to fixed time or
kilometres/miles intervals. If, during
each operation, in addition to the ones
scheduled, the need arises for further
replacements or repairs, these may be
carried out with the owner's explicit
agreement only.
IMPORTANT NOTES
The scheduled service deadlines are
set out by the Manufacturer. Failure to
have them carried out may invalidate
the warranty.
We advise sharing any doubts
regarding the car’s proper operation
with your Fiat Dealership, before
waiting for the next scheduled service
deadline.
233
SERVICE SCHEDULE
WARNING Once you have carried out the last intervention in the table, continue with the scheduled servicing, maintaining the
frequency indicated in the plan by marking each operation with a dot or dedicated note.
Warning: simply restarting the maintenance from the start of the plan may cause the allowed interval to be exceeded for some
operations!
Thousands of miles
9
18
27
36
45
54
63
72
81
90
Thousands of kilometres
15
30
45
60
75
90
105
120
135
150
Years
1
2
3
4
5
6
7
8
9
10
Check the tyre condition/wear and, if necessary, adjust the
pressure. Check the "Fix&Go” kit condition/expiry
Check operation of lighting system (headlights, direction indicators,
hazard warning lights, boot, passenger compartment, glove
compartment, instrument panel warning lights, etc.)
Check and, if necessary, top up fluid levels (high-voltage cooling,
brakes, windscreen washer, etc.) (1)
Check vehicle functions via diagnostic socket (vehicle control units,
high-voltage battery, etc.)
Check 12V battery with special instrument
Visually inspect the condition of: exterior bodywork, underbody
protection, pipes and hoses (brakes, climate control system, cooling
system), rubber parts (boots, sleeves, bushes, etc.)
Check windscreen/rear window wiper blade position/wear (where
provided)
Check operation of the windscreen wiper/washer system and adjust
nozzles, if necessary
234
Thousands of miles
9
18
27
36
45
54
63
72
81
90
Thousands of kilometres
15
30
45
60
75
90
105
120
135
150
Years
1
2
3
4
5
6
7
8
9
10
Check cleanliness of hood and boot locks, cleanliness and
lubrication of linkage
Check soft top operation while closing and opening; check of seals
and lubrication of canvas sliding side guide (only cabrio versions)
Visually inspect conditions and wear of front disc brake pads and
operation of pad wear indicator (where present)
Visually inspect condition and wear of the rear drum brake lining
Change the brake fluid
(4)
Replace passenger compartment filter (2) (
)
(
)
Replace UConnect Box system battery (3)
Visually check charging port
(1) Topping up must be carried out with the fluids indicated in this Owner Handbook and only after checking that the system is undamaged.
(2) If the car is used in dusty areas, this cleaner should be replaced every 15,000 km/9,000 mi.
(3) The Uconnect Box battery must be replaced every 5 years, regardless of mileage.
(4) Brake fluid must be changed every 2 years or every 75,000 km/45,000 mi.
(
) Recommended operations
(
) Mandatory operations
235
REGULAR CHECKS
DEMANDING USE OF THE
Every 1,000 km/600 mi or before
CAR
long journeys, check and top up the
If the car is mainly used in one of the
following, if necessary:
following particularly harsh conditions:
traction system coolant level;
dusty roads;
NOTE The motor coolant level must
short, repeated journeys (less than
be checked when the motor is cold
7-8 km / 4-5 mi) at sub-zero external
and must range between the MIN
temperatures;
and MAX marks on the reservoir. If
in the event of a long period of
the level is under the MIN level, go to
inactivity;
a Fiat Dealership. Do not attempt to
perform the following inspections more
open the cap yourself to avoid burns
frequently than shown on the Service
and/or damage to the cooling system
Schedule:
and electronic components. Topping
check front disc brake pad condition
up and filling operations must be
and wear;
carried out by qualified personnel at
check cleanliness of bonnet and boot
Fiat Dealership using the appropriate
locks, cleanliness and lubrication of
equipment for vacuum filling.
linkage;
visually inspect conditions of:
brake fluid level;
electric motor, transmission, brake
windscreen washer fluid level;
tyre inflation pressure and condition;
pipes and hoses, rubber elements
operation of lighting system
(gaiters/sleeves/bushes, etc.);
check the state of charge and fluid
(headlights, direction indicators, hazard
level (electrolyte) of the 12V battery;
warning lights, etc.);
operation of windscreen
check and, if necessary, replace
washer/wiper system and
pollen filter.
positioning/wear of windscreen/rear
window wiper blades.
You are advised to use PETRONAS
LUBRICANTS products, which
have been designed and produced
specifically for Fiat cars (see table
“Capacities” in the “Technical
specifications” section).
236
CHECKING LEVELS
241) 242) 243)
87)
248
F0S1087
A. Motor coolant B. Brake fluid C. 12V battery D. Windscreen washer fluid
WARNING
241) Never smoke while working in the engine compartment: gas and inflammable vapours may be present, with the risk of fire.
242) Be very careful when working in the engine compartment when the engine is hot: you may get burned. Remember that the fan may start
up if the engine is hot: this could injure you. Scarves, ties and other loose clothing might be pulled by moving parts.
243) Do not operate in the engine compartment while the vehicle is charging or when the connector on the charging port is plugged in.
237
IMPORTANT
87) The use of products with specifications other than those indicated above could cause damage to the engine not covered by the warranty.
238
COOLING SYSTEM FLUID
BRAKE FLUID
WARNING
The traction system coolant level must
Check that the fluid is at the maximum
be checked when the motor is cold
level (the fluid level in the reservoir must
244) Do not travel with the windscreen
and must range between the MIN
not exceed the MAX mark).
washer fluid reservoir empty: the
and MAX marks on the reservoir. If
If the fluid level in the reservoir is too
windscreen washer is essential for
the level is under the MIN level, go to
low, undo reservoir cap (B) (see
improving visibility. Some commercial
a Fiat Dealership. Do not attempt to
the previous pages) and add the
windscreen washer additives are
open the cap yourself to avoid burns
fluid described in the "Technical
flammable. The engine compartment
contains hot components which may set it
and/or damage to the cooling system
specifications" section.
on fire.
and electronic components. Topping
Note Carefully clean the cap of the
245) Brake fluid is poisonous and highly
up and filling operations must be
reservoir (B) and the surrounding
corrosive. In the event of accidental
carried out by qualified personnel at
contact, immediately wash the affected
surface. Take great care to ensure that
Fiat Dealership using the appropriate
parts with water and mild soap. Then rinse
impurities do not enter the reservoir
thoroughly. Call a doctor immediately if
equipment for vacuum filling.
when the cap is opened. Always use a
swallowed.
WINDSCREEN/REAR
funnel with a built-in filter with a mesh
246) The symbol on the reservoir
WINDOW WASHER FLUID
of 0.12 mm or less.
identifies synthetic brake fluids,
distinguishing them from the mineral type.
Check fluid level through the reservoir.
Use of mineral type fluids will irreparably
If the liquid is too low, lift reservoir
WARNING Brake fluid is hygroscopic
damage the braking system’s special
cap (D) (see previous pages) and add
(i.e. it absorbs moisture). For this
rubber seals.
the fluid described in In the section
reason, if the car is mainly used
"Technical specifications".
in areas with a high degree of
IMPORTANT
The windscreen washer reservoir must
atmospheric humidity, the fluid
be filled with the liquids provided for
must be replaced at more frequent
88) Prevent brake fluid, which is highly
intervals than specified on the "Service
this purpose. The use of any other
corrosive, from coming into contact
Schedule".
liquid can compromise the operation of
with painted parts. Should it happen,
the reservoir pump.
immediately wash with water.
After topping up, close cap (D), making
245) 246)
sure it is correctly locked.
88)
244)
239
12V BATTERY
USEFUL ADVICE FOR
The battery will also be more at risk
EXTENDING THE LIFE OF
of freezing (this can happen as early
The car is fitted with a low-
THE 12V BATTERY
as -10°C). Refer to the "Car inactivity"
maintenance 12V battery: no electrolyte
To avoid draining your 12V battery
chapter in the "Starting and driving"
top-ups with distilled water are needed
and make it last longer, observe the
section if the car is left parked for a
in standard conditions of use.
following instructions:
long time.
when you park the car, ensure
If after buying the car, you want to
WARNING It is forbidden to disconnect
that the doors, tailgate and bonnet
install electric accessories which
the 12V battery. For 12V battery
are closed properly, to prevent any
require permanent electric supply
replacement, contact a Fiat Dealership.
lights from remaining on inside the
(alarm, etc.) or accessories influencing
passenger's compartment;
the electrical supply requirements,
WARNING Do not use the 12V battery
switch off all roof lights inside the
contact a Fiat Dealership whose
of the car to charge the 12V battery of
car: the car is however equipped with a
qualified personnel will suggest
the another car. The battery power is
system which switches all internal lights
the most suitable devices from
insufficient for this operation, with the
off automatically;
Lineaccessori MOPAR
®andevaluate
risk of damage to the car.
do not keep accessories (e.g. radio,
the overall electric absorption, checking
hazard warning lights, etc.) switched on
whether the electric system in the car is
for a long time;
able to support the required load, or
INSPECTING THE
before performing any operation
if it should be integrated with a more
CHARGE AND THE
on the electrical system, disconnect
powerful 12V battery.
ELECTROLYTE LEVEL
the cable from the negative battery
Since some of these devices continue
The operations must be carried out as
terminal;
to consume electricity even when the
described in this Owner Handbook only
completely tighten the battery
motor is off, they gradually run down
by specialised technicians. Topping
terminals.
the battery.
must be carried out by specialised
personnel at a Fiat Dealership.
RECHARGING THE 12V
247) 248)
WARNING If the charge level remains
BATTERY
under 50% for a long time, the 12V
251)
12V BATTERY
battery is damaged by sulphation,
REPLACEMENT
Never charge the 12V battery using:
reducing its capacity and efficiency at
WARNING For battery replacement,
an external battery charger;
start-up.
contact a Fiat Dealership.
a battery from another car.
Contact a Fiat Dealership.
249) 250)
89)
7)
240
BRAKES
WARNING
IMPORTANT
Depending on the version/market, the
247) Battery fluid is poisonous and
7) Batteries contain substances which
car may be equipped with mechanical
corrosive. Avoid contact with the skin and
are very harmful for the environment. It is
wear detectors for the brake pads: one
eyes. Keep open flames away from the
advisable to contact a Fiat Dealership for
for each wheel assembly. When the
battery and do not use objects that might
battery replacement.
brake linings are close to wearing out,
create sparks: risk of explosion and fire.
pressing the brake pedal will generate
248) Using the battery with low fluid will
irreparably damage the battery and may
RUBBER HOSES
a slight squeal: this lasts for about
cause an explosion.
100 km (the mileage varies with the
As far as the maintenance of the brake
249) Always wear appropriate goggles to
driving style and route). In this case,
protect your eyes when working on or near
system and cooling system rubber
it is still possible to continue driving,
the conventional battery.
hoses is concerned, follow the "Service
with caution. However, contact a Fiat
250) Any operation concerning the 12V
Schedule" in this section carefully.
Dealership as soon as possible to have
battery ( removal, disconnection, etc.)
Ozone, high temperatures and
must be carried out by a specialised
the worn brake pads changed.
prolonged lack of fluid in the system
professional. Contact a Fiat Dealership.
may cause hardening and cracking of
REPLACING THE
251) Do not attempt to recharge a frozen
battery: first it must be thawed, otherwise
the hoses, with possible leaks. Careful
WINDSCREEN/REAR
there is a risk of explosion. If freezing has
checking is therefore necessary.
WINDOW WIPER
occurred, the battery should be checked
by specialised technicians to make sure
BLADES
that the internal elements are not damaged
and that the body is not cracked, with the
WIPER BLADES
risk of leaking poisonous and corrosive
Replace the blades if the rubber
acid.
edge is deformed or worn. In any
case, it is advisable to replace them
IMPORTANT
approximately once a year.
A few simple precautions can reduce
89) Incorrect installation of electric and
the possibility of damage to the blades:
electronic devices may cause severe
if the temperature falls below zero,
damage to your car. After purchasing your
make sure that ice has not frozen the
car, if you wish to install any accessories
rubber to the glass. Use a de-icing
(anti-theft, etc.), go to a Fiat Dealership,
which will suggest the most suitable
product to release it if required;
devices and advise you whether a higher
remove any snow from the glass:
capacity battery needs to be installed.
in addition to protecting the blades,
241
|
||
|
|
|