Chrysler Voyager. Manual - part 358

 

  Index      Chrysler     Chrysler Voyager - service and repair manual

 

Search            copyright infringement  

 

 

 

 

 

 

 

 

 

Content   ..  356  357  358  359   ..

 

 

Chrysler Voyager. Manual - part 358

 

 

TEST

ACTION

APPLICABILITY

4

Remove the Power Liftgate Motor trim panel.
Remove the Liftgate trim panel.
Disconnect the Power Liftgate Module C2 connector.
Disconnect the Right Pinch Sensor connector
Measure the resistance between ground and the Pinch Sensor Signal circuit.
Is the resistance below 100.0 ohms?

All

Yes

→ Go To 5

No

→ Replace the Right Pinch Sensor.

Perform BODY VERIFICATION TEST - VER 1.

5

Remove the Liftgate trim panel.
Disconnect the Right Pinch Sensor connector.
Disconnect the Left Pinch Sensor connector.
Measure the resistance between ground and the Right Pinch Sensor Signal circuit.
Is the resistance below 1000.0 ohms?

All

Yes

→ Repair the Right Pinch Sensor Signal wire for a short to ground.

Perform BODY VERIFICATION TEST - VER 1.

No

→ Go To 6

6

Remove the Power Liftgate Motor trim panel.
Remove the liftgate trim panel.
Disconnect the Power Liftgate Module C2 connector.
Disconnect the Left Pinch Sensor connector
Measure the resistance between ground and the Pinch Sensor Signal circuit.
Is the resistance below 100.0 ohms?

All

Yes

→ Go To 7

No

→ Replace the Left Pinch Sensor.

Perform BODY VERIFICATION TEST - VER 1.

7

If there are no possible causes remaining, view repair.

All

Repair

Repair the Pinch Sensor Signal wire for a short to ground.
Perform BODY VERIFICATION TEST - VER 1.

859

POWER DOORS - LIFTGATE

PINCH SENSOR SIGNAL CIRCUIT SHORT TO GROUND —

Continued

Symptom:

*POWER LIFTGATE INOPERATIVE

POSSIBLE CAUSES

DTC’S PRESENT

MODULE RESPONSE

INTERMITTENT PROBLEM

SYSTEM TESTS

TEST

ACTION

APPLICABILITY

1

With the DRBIII

t check for response from the Body Computer and the Power

Liftgate Modules
Is there response from both modules?

All

Yes

→ Go To 2

No

→ Refer to symptom list for problems related to COMMUNICA-

TION.

2

With the DRBIII

t, read DTCs in POWER LIFTGATE and BODY COMPUTER.

Are any Power Liftgate related codes present?

All

Yes

→ Refer to symptom list for problems related to POWER LIFT-

GATE.

No

→ Go To 3

3

This test will determine what inhibited the Power Liftgate from operating properly.
With the DRBIII

t, select POWER LIFTGATE, MISCELLANEOUS, LAST INHIBIT

MONITOR.
Does the DRBIII

t display any INHIBIT REASONS?

All

Yes

→ Check for any binding conditions or other restrictions that may

prevent proper operation. Using the wiring diagram/schematic as
a guide, inspect the wiring and connectors.

No

→ Go To 4

4

Ensure Liftgate is fully closed before proceeding.
With the DRBIII

t select SYSTEM TEST.

Perform the Open, Close, Latch Cinch, Latch Release and Relay tests.
Did any test fail?

All

Yes

→ Using the wiring diagram/schematic as a guide, inspect the

wiring and connectors.

No

→ Test Complete.

860

POWER DOORS - LIFTGATE

Symptom:

AMBIENT TEMPERATURE SENSOR CIRCUIT OPEN

When Monitored and Set Condition:

AMBIENT TEMPERATURE SENSOR CIRCUIT OPEN

When Monitored:

Anytime the Power Sliding Door Module is awake.

Set Condition:

If the Power Sliding Door Modules internal thermistor becomes open, this

code will set.

POSSIBLE CAUSES

DTC PRESENT

POWER SLIDING DOOR MODULE

TEST

ACTION

APPLICABILITY

1

With the DRBIII

t, record and erase DTC’s.

Turn the ignition off, wait 10 seconds, then turn the ignition on.
Operate the power sliding door several times from stop to stop if possible.
With the DRBIII

t, read ACTIVE DTCs.

Does the DRBIII

t display AMBIENT TEMPERATURE SENSOR CIRCUIT HIGH?

All

Yes

→ Replace the Power Sliding Door Module.

Perform BODY VERIFICATION TEST - VER 1.

No

→ No problem found at this time.

Perform BODY VERIFICATION TEST - VER 1.

861

POWER DOORS - SLIDING

Symptom:

AMBIENT TEMPERATURE SENSOR CIRCUIT SHORT TO GROUND

When Monitored and Set Condition:

AMBIENT TEMPERATURE SENSOR CIRCUIT SHORT TO GROUND

When Monitored:

Anytime the Power Sliding Door Module is awake.

Set Condition:

If the Power Sliding Door Modules internal thermistor is shorted, this

code will set.

POSSIBLE CAUSES

DTC PRESENT

POWER SLIDING DOOR MODULE

TEST

ACTION

APPLICABILITY

1

With the DRBIII

t, record and erase DTC’s.

Turn the ignition off, wait 10 seconds, then turn the ignition on.
Operate the power sliding door several times from stop to stop if possible.
With the DRBIII

t, read ACTIVE DTCs.

Does the DRBIII

t display AMBIENT TEMPERATURE SENSOR CIRCUIT LOW?

All

Yes

→ Replace the Power Sliding Door Module.

Perform BODY VERIFICATION TEST - VER 1.

No

→ No problem found at this time.

Perform BODY VERIFICATION TEST - VER 1.

862

POWER DOORS - SLIDING

 

 

 

 

 

 

 

Content   ..  356  357  358  359   ..