Chrysler Voyager. Manual - part 349

 

  Index      Chrysler     Chrysler Voyager - service and repair manual

 

Search            copyright infringement  

 

 

 

 

 

 

 

 

 

Content   ..  347  348  349  350   ..

 

 

Chrysler Voyager. Manual - part 349

 

 

TEST

ACTION

APPLICABILITY

2

Examine the liftgate for proper alignment, worn or binding hinges, weak or binding
liftgate prop rods, loose/ hard weatherstrip, and gear teeth on the power liftgate
motor assembly for wear or anything that would cause an obstruction to proper
operation.
Compare the effort needed on the disabled vehicle.
Especially notice the effort needed to unlatch and close the liftgate.
Does it take more effort to operate the liftgate than it should?

All

Yes

→ Refer to Service information for the related symptom(s).

Perform BODY VERIFICATION TEST - VER 1.

No

→ Go To 3

3

Turn the ignition off.
Disconnect the Power Liftgate Module C1 connector.
Using a 12-volt test light connected to 12-volts, check the Ground circuit.
Wiggle the harness and check for an intermittent open condition.
Does the test light illuminate brightly?

All

Yes

→ Go To 4

No

→ Repair the Ground circuit for an open.

Perform BODY VERIFICATION TEST - VER 1.

4

Turn the ignition off.
Disconnect the Power Liftgate Module C1 connector.
Measure the resistance between ground and the Liftgate Close Driver circuit.
Wiggle the harness and check for an intermittent short circuit condition.
Is the resistance below 1000.0 ohms?

All

Yes

→ Repair the Liftgate Close Driver circuit for a short to ground.

Perform BODY VERIFICATION TEST - VER 1.

No

→ Go To 5

5

Turn the ignition off.
Disconnect the Power Liftgate Module C2 connector.
Measure the resistance between ground and the Liftgate Latch Release Driver
circuit.
Wiggle the harness and check for an intermittent short condition.
Is the resistance below 1000.0 ohms?

All

Yes

→ Repair the Liftgate Latch Release Driver circuit for a short to

ground.
Perform BODY VERIFICATION TEST - VER 1.

No

→ Go To 6

6

Turn the ignition off.
Disconnect the Power Liftgate Module C2 connector.
Measure the resistance between the Ground circuit (cavity 20) and the Liftgate Latch
Release Driver circuit.
Wiggle the harness and check for an intermittent short condition.
Is the resistance below 1000.0 ohms?

All

Yes

→ Repair the Liftgate Latch Release Driver circuit for a short to the

Ground circuit.
Perform BODY VERIFICATION TEST - VER 1.

No

→ Go To 7

823

POWER DOORS - LIFTGATE

INCOMPLETE POWER CLOSE - OVER CURRENT —

Continued

TEST

ACTION

APPLICABILITY

7

Turn the ignition off.
Disconnect the Power Liftgate Module C2 connector.
Measure the resistance between ground and the Liftgate Gear Engage Driver circuit.
Wiggle the harness and check for an intermittent short condition.
Is the resistance below 1000.0 ohms?

All

Yes

→ Repair the Liftgate Gear Engage Driver circuit for a short to

ground.
Perform BODY VERIFICATION TEST - VER 1.

No

→ Go To 8

8

Turn the ignition off.
Disconnect the Power Liftgate Module C2 connector.
Measure the resistance between the Ground circuit (cavity 20) and the Liftgate Gear
Engage Driver circuit.
Wiggle the harness and check for an intermittent short condition.
Is the resistance below 1000.0 ohms?

All

Yes

→ Repair the Liftgate Gear Engage Driver circuit for a short to the

Ground circuit.
Perform BODY VERIFICATION TEST - VER 1.

No

→ Go To 9

9

Ensure all module and motor connectors are connected at this time.
Try to operate the liftgate in the close position.
Did the motor start to close the liftgate but was very slow and labored extensively?

All

Yes

→ Replace the Power Liftgate Motor assembly.

Perform BODY VERIFICATION TEST - VER 1.

No

→ Replace the Power Liftgate Module

Perform BODY VERIFICATION TEST - VER 1.

824

POWER DOORS - LIFTGATE

INCOMPLETE POWER CLOSE - OVER CURRENT —

Continued

Symptom:

INCOMPLETE POWER CLOSE - TRANSISTOR SHORTED

When Monitored and Set Condition:

INCOMPLETE POWER CLOSE - TRANSISTOR SHORTED

When Monitored:

Whenever the power liftgate is performing a power close operation.

Set Condition:

The Power Liftgate Module detects that the motor is rotating (monitors

hall effect pulses) even though the controlled PWM rate is 0 percent. This DTC is set
during the power close (2 second chime period, prior to movement of the liftgate) operation.

POSSIBLE CAUSES

DTC PRESENT

POWER LIFTGATE MODULE

TEST

ACTION

APPLICABILITY

1

With the DRBIII

t, record and erase DTC’s.

Turn the ignition off, wait 10 seconds, then turn the ignition on.
Operate the power liftgate several times if possible.
With the DRBIII

t, read ACTIVE DTCs.

Does the DRBIII

t display INCOMPLETE POWER CLOSE - TRANSISTOR

SHORTED?

All

Yes

→ Replace the Power Liftgate Module.

Perform BODY VERIFICATION TEST - VER 1.

No

→ Using the wiring diagram/schematic as a guide, inspect the

wiring and connectors for an intermittent condition. Operate the
liftgate several times and check for any binding conditions.
Perform BODY VERIFICATION TEST - VER 1.

825

POWER DOORS - LIFTGATE

Symptom:

INCOMPLETE POWER CLOSE - VOLTAGE BELOW MINIMUM
LEVEL

When Monitored and Set Condition:

INCOMPLETE POWER CLOSE - VOLTAGE BELOW MINIMUM LEVEL

When Monitored:

Whenever the power liftgate is performing a power close operation.

Set Condition:

The PLG Module detects that the voltage is below 9.5 volts during the

power close operation.

POSSIBLE CAUSES

DTC PRESENT

MODULE VOLTAGE LOW

BINDING LIFTGATE

DRB OPERATING VOLTAGE LOW

PLG MODULE - HIGH RESISTANCE

POWER LIFTGATE MOTOR

TEST

ACTION

APPLICABILITY

1

With the DRBIII

t, record and erase DTC’s.

Turn the ignition off, wait 10 seconds, then turn the ignition on.
Operate the power liftgate several times if possible.
With the DRBIII

t, read DTCs.

Does the DRBIII

t display INCOMPLETE POWER CLOSE - VOLTAGE BELOW

MINIMUM LEVEL?

All

Yes

→ Go To 2

No

→ Using the wiring diagram/schematic as a guide, inspect the

wiring and connectors for an intermittent condition. Operate the
door several times and check for any binding conditions.
Perform BODY VERIFICATION TEST - VER 1.

2

Examine the liftgate for proper fit and alignment, or anything that would cause an
obstruction to proper operation.
Check the prop rods to ensure liftgate will fall closed from the approximately 3/4
closed position.
Does it take more effort to operate the liftgate than it should?

All

Yes

→ Refer to Service information for the related symptom(s).

Perform BODY VERIFICATION TEST - VER 1.

No

→ Go To 3

826

POWER DOORS - LIFTGATE

 

 

 

 

 

 

 

Content   ..  347  348  349  350   ..