Chrysler Voyager. Manual - part 331

 

  Index      Chrysler     Chrysler Voyager - service and repair manual

 

Search            copyright infringement  

 

 

 

 

 

 

 

 

 

Content   ..  329  330  331  332   ..

 

 

Chrysler Voyager. Manual - part 331

 

 

Symptom:

*REPAIRING CMTC DISPLAYS DOUBLE DASH ( - - ) IN TEMP
DISPLAY

POSSIBLE CAUSES

NO RESPONSE - PCI BUS - FRONT CONTROL MODULE

CMTC BUS MESSAGE FAILURE

COMPASS MINI-TRIP COMPUTER

AMBIENT TEMPERATURE SENSOR

AMBIENT TEMPERATURE SENSOR SIGNAL CIRCUIT SHORT TO SENSOR CIRCUIT

AMBIENT TEMPERATURE SENSOR SIGNAL CIRCUIT SHORT TO GROUND

AMBIENT TEMPERATURE SENSOR SIGNAL CIRCUIT OPEN

AMBIENT TEMPERATURE SENSOR RETURN CIRCUIT OPEN

INTELLIGENT POWER MODULE

FRONT CONTROL MODULE

TEST

ACTION

APPLICABILITY

1

Turn the ignition on.
With the DRBIII

t, select System Monitors, J1850 Module Scan.

Does the DRBIII

t display FCM on the BUS?

All

Yes

→ Go To 2

No

→ Refer to the COMMUNICATIONS category and perform the

appropriate symptom.

2

Turn the ignition on.
With the DRBIII

t, select Body, Compass Mini-Trip, System Tests, then Auto Self

Test.
Does the DRBIII

t display TEST FAILED: Bus Message Failure?

All

Yes

→ Refer to the COMMUNICATIONS category and perform the

appropriate symptom.

No

→ Go To 3

3

Turn the ignition on.
With the DRBIII

t, select Body, Compass Mini-Trip, System Tests, then Auto Self

Test.
Does the DRBIII

t display TEST FAILED: Internal EVIC Failure?

All

Yes

→ Replace the Compass Mini-Trip Computer in accordance with the

Service Information.
Perform BODY VERIFICATION TEST - VER 1.

No

→ Go To 4

751

OVERHEAD CONSOLE

TEST

ACTION

APPLICABILITY

4

Turn the ignition off.
Disconnect the Ambient Temperature Sensor harness connector.
Check connectors - Clean/repair as necessary.
Measure the resistance of the Ambient Temperature Sensor.
0°C (32°F) Sensor Resistance = 29.33 - 35.99 kilohms
10°C (50°F) Sensor Resistance = 17.99 - 21.81 kilohms
20°C (68°F) Sensor Resistance = 11.37 - 13.61 kilohms
30°C (86°F) Sensor Resistance = 7.37 - 8.75 kilohms
40°C (104°F) Sensor Resistance = 4.90 - 5.75 kilohms
Does the Ambient Temperature Sensor measure within specifications?

All

Yes

→ Go To 5

No

→ Replace the Ambient Temperature Sensor in accordance with the

Service Information.
Perform BODY VERIFICATION TEST - VER 1.

5

Turn the ignition off.
Disconnect the Ambient Temperature Sensor harness connector.
Disconnect the IPM C1 harness connector.
Check connectors - Clean/repair as necessary.
Measure the resistance of the Ambient Temperature Sensor Signal circuit to the
Sensor Return circuit.
Does the resistance measure less than 5.0 ohms?

All

Yes

→ Repair the Ambient Temperature Sensor Signal circuit for a short

to the Sensor Return circuit.
Perform BODY VERIFICATION TEST - VER 1.

No

→ Go To 6

6

Turn the ignition off.
Disconnect the Ambient Temperature Sensor harness connector.
Disconnect the IPM C1 harness connector.
Check connectors - Clean/repair as necessary.
Measure the resistance of the Ambient Temperature Sensor Signal circuit to ground.
Does the resistance measure less than 5.0 ohms?

All

Yes

→ Repair the Ambient Temperature Sensor Signal circuit for a short

to ground.
Perform BODY VERIFICATION TEST - VER 1.

No

→ Go To 7

7

Turn the ignition off.
Disconnect the Ambient Temperature Sensor harness connector.
Disconnect the IPM C1 harness connector.
Check connectors - Clean/repair as necessary.
Measure the resistance of the Ambient Temperature Sensor Signal circuit.
Does the resistance measure less than 5.0 ohms?

All

Yes

→ Go To 8

No

→ Repair the Ambient Temperature Sensor Signal circuit for an

open.
Perform BODY VERIFICATION TEST - VER 1.

752

OVERHEAD CONSOLE

*REPAIRING CMTC DISPLAYS DOUBLE DASH ( - - ) IN TEMP DISPLAY

Continued

TEST

ACTION

APPLICABILITY

8

Turn the ignition off.
Disconnect the Ambient Temperature Sensor harness connector.
Disconnect the IPM C1 harness connector.
Check connectors - Clean/repair as necessary.
Measure the resistance of the Ambient Temperature Sensor Return circuit.
Does the resistance measure less than 5.0 ohms?

All

Yes

→ Go To 9

No

→ Repair the Ambient Temperature Sensor Return circuit for an

open.
Perform BODY VERIFICATION TEST - VER 1.

9

Turn the ignition off.
Disconnect and isolate the battery negative cable.
Disconnect the IPM C1 harness connector.
Disconnect the FCM from the IPM.
Check connectors - Clean/repair as necessary.
Measure the resistance of the Ambient Temperature Sensor Signal circuit and the
Return circuit through the IPM.
Does each circuit resistance measure less than 5.0 ohms?

All

Yes

→ Replace the Front Control Module in accordance with the Service

Information.
Perform BODY VERIFICATION TEST - VER 1.

No

→ Replace the Intelligent Power Module in accordance with the

Service Information.
Perform BODY VERIFICATION TEST - VER 1.

753

OVERHEAD CONSOLE

*REPAIRING CMTC DISPLAYS DOUBLE DASH ( - - ) IN TEMP DISPLAY

Continued

Symptom:

DRIVER DOOR LOCK SWITCH INPUT OPEN OR SHORT TO VOLT-
AGE

When Monitored and Set Condition:

DRIVER DOOR LOCK SWITCH INPUT OPEN OR SHORT TO VOLTAGE

When Monitored:

At all times when battery power is supplied to the Body Control

Module.

Set Condition:

When the BCM senses voltage to the door lock switch above 4.6 volts for

over 10 seconds.

POSSIBLE CAUSES

DTC PRESENT

BODY CONTROL MODULE - DRIVER DOOR LOCK SWITCH VOLTAGE LOW

DOOR LOCK SWITCH GROUND OPEN

DOOR LOCK SWITCH MUX CIRCUIT OPEN

DOOR LOCK SWITCH OPEN

DOOR LOCK SWITCH MUX CIRCUIT SHORT TO VOLTAGE

BODY CONTROL MODULE - DOOR LOCK SWITCH MUX SHORT TO VOLTAGE

TEST

ACTION

APPLICABILITY

1

With the DRBIII

t, record and erase DTC’s.

Cycle the ignition switch from ON to OFF to ON.
With the DRBIII

t, read DTC’s.

Remove the key and operate the door locks from the Driver Door Lock Switch while
monitoring the DRBIII

t.

Wait 10 seconds.
Does the DRBIII

t display DR DOOR LOCK SW INPUT OPEN OR SHORT TO

VOLTAGE?

All

Yes

→ Go To 2

No

→ Using the wiring diagram/schematic as a guide, inspect the

wiring and connectors.
Perform BODY VERIFICATION TEST - VER 1.

2

With the DRBIII

t in Sensors, read the DR DOOR LOCK SW voltage.

Does the DRBIII

t display 4.3 volts or greater?

All

Yes

→ Go To 3

No

→ Disconnect the BCM harness connector(s). Check connectors -

Clean/repair as necessary. If okay, replace the Body Control
Module.
Perform BODY VERIFICATION TEST - VER 1.

754

POWER DOOR LOCKS/RKE

 

 

 

 

 

 

 

Content   ..  329  330  331  332   ..