Chrysler Voyager. Manual - part 186

 

  Index      Chrysler     Chrysler Voyager - service and repair manual

 

Search            copyright infringement  

 

 

 

 

 

 

 

 

 

Content   ..  184  185  186  187   ..

 

 

Chrysler Voyager. Manual - part 186

 

 

Symptom:

*AIRBAG INDICATOR ON WITHOUT ACTIVE TROUBLE CODES

POSSIBLE CAUSES

AIRBAG WARNING INDICATOR ON WITHOUT ACTIVE TROUBLE CODES

INSTRUMENT CLUSTER PROBLEMS

TEST

ACTION

APPLICABILITY

1

NOTE: Ensure the battery is fully charged.
Turn the ignition on.
Make sure that all active DTC’s have been repaired before performing this procedure.
With the DRBIII

t select the PASSIVE RESTRAINTS, AIRBAG, MONITOR DIS-

PLAY and read the WARNING LAMP STATES.
With no active DTCs, Does the LAMP REQ by ACM monitor show ON?

All

Yes

→ WARNING: MAKE SURE THE BATTERY IS DISCONNECTED,

THEN WAIT TWO MINUTES BEFORE PROCEEDING. Replace
the Airbag Control Module in accordance with Service Instruc-
tions.
Perform AIRBAG VERIFICATION TEST - VER 1.

No

→ Refer to INSTRUMENT CLUSTER CATEGORY symptom list for

problems related to Instrument Cluster.
Perform AIRBAG VERIFICATION TEST - VER 1.

NOTE: When reconnecting Airbag system components, the ignition must be
turned off and the battery must be disconnected.

171

AIRBAG

Symptom:

ALL OUTPUTS SHORT

When Monitored and Set Condition:

ALL OUTPUTS SHORT

When Monitored:

Ignition in RUN and IOD fuse installed.

Set Condition:

The radio has sensed a short on the output for more than 10 seconds.

POSSIBLE CAUSES

DETERMINE FAULT

FRONT SHORTED SPEAKER

REAR SHORTED SPEAKER

(+) CIRCUIT SHORTED TO GROUND

(-) CIRCUIT SHORTED TO GROUND

SPEAKER (+) & (-) CIRCUITS SHORTED TOGETHER

SPEAKER SECTION OF RADIO

TEST

ACTION

APPLICABILITY

1

Turn the ignition on.
Turn the Radio on.
With the DRBIII

t, erase the audio DTC’s.

Cycle the ignition switch from off to on and wait 10 seconds.
With the DRBIII

t, read the audio DTC’s.

Does the DRBIII

t display ALL OUTPUTS SHORT?

All

Yes

→ Go To 2

No

→ Refer to the wiring diagrams located in the service information to

help isolate a possible intermittent short.
Perform BODY VERIFICATION TEST - VER 1.

172

AUDIO

TEST

ACTION

APPLICABILITY

2

Turn the ignition off.
NOTE: Perform this procedure after disconnecting each front speaker
connector.
Disconnect each front speaker harness connector one at a time.
Turn the ignition on.
Turn the radio on.
With the DRBIII

t, erase the audio DTCs.

Cycle the ignition switch from off to on and wait 10 seconds.
With the DRBIII

t, read DTC’s.

Does the DRBIII

t display ALL OUTPUTS SHORT with all the front speakers

disconnected?

All

Yes

→ Go To 3

No

→ Replace the Speaker that when disconnected the DTC did not

reset. Note: On the premium system, check the I/P speaker
circuits between the front door speaker and the I/P speaker for a
short to ground or shorted together condition before replacing
speaker.
Perform BODY VERIFICATION TEST - VER 1.

3

Turn the ignition off.
NOTE: Perform this procedure after disconnecting each rear speaker
connector.
Disconnect each rear speaker harness connector one at a time.
Turn the ignition on.
Turn the radio on.
With the DRBIII

t, erase the audio DTCs.

Cycle the ignition switch from off to on and wait 10 seconds.
With the DRBIII

t, read DTC’s.

Does the DRBIII

t display ALL OUTPUTS SHORT with all the rear speakers

disconnected?

All

Yes

→ Go To 4

No

→ Replace Speaker that when disconnected the DTC did not reset.

Note: On the premium system, check the rear speaker ckts
between the rear door speaker and the rear pillar speaker for a
short to ground or shorted together condition before replacing
speaker.
Perform BODY VERIFICATION TEST - VER 1.

4

Turn the ignition off.
Disconnect each front and rear speaker harness connector.
Disconnect the Radio C1 harness connector.
Measure the resistance between ground and each speaker (+) circuit.
Is the resistance below 1000.0 (1K) ohms?

All

Yes

→ Repair the speaker (+) circuit for a short to ground.

Perform BODY VERIFICATION TEST - VER 1.

No

→ Go To 5

173

AUDIO

ALL OUTPUTS SHORT —

Continued

TEST

ACTION

APPLICABILITY

5

Turn the ignition off.
Disconnect each front and rear speaker harness connector.
Disconnect the Radio C1 harness connector.
Measure the resistance between ground and each speaker (-) circuit.
Is the resistance below 1000.0 (1K) ohms?

All

Yes

→ Repair the speaker (-) circuit for a short to ground.

Perform BODY VERIFICATION TEST - VER 1.

No

→ Go To 6

6

Turn the ignition off.
Disconnect each front and rear speaker harness connector.
Disconnect the Radio C1 harness connector.
Measure the resistance between each speaker (+) circuit and each speaker (-) circuit.
Is the resistance below 1000.0 (1K) ohms for any of the measurements?

All

Yes

→ Repair the speaker circuits shorted together.

Perform BODY VERIFICATION TEST - VER 1.

No

→ Go To 7

7

If there are no possible causes remaining, view repair.

All

Repair

Replace the Radio.
Perform BODY VERIFICATION TEST - VER 1.

174

AUDIO

ALL OUTPUTS SHORT —

Continued

 

 

 

 

 

 

 

Content   ..  184  185  186  187   ..