Chrysler Voyager. Manual - part 54

 

  Index      Chrysler     Chrysler Voyager - service and repair manual

 

Search            copyright infringement  

 

 

 

 

 

 

 

 

 

Content   ..  52  53  54  55   ..

 

 

Chrysler Voyager. Manual - part 54

 

 

TEST

ACTION

APPLICABILITY

3

WARNING: WHEN THE ENGINE IS OPERATING, DO NOT STAND IN A
DIRECT LINE WITH THE FAN. DO NOT PUT YOUR HANDS NEAR THE
PULLEYS, BELTS OR FAN. DO NOT WEAR LOOSE CLOTHING.
NOTE: The conditions that set the DTC are not present at this time. The
following list may help in identifying the intermittent condition.
With the engine running at normal operating temperature, monitor the DRBIII

t

parameters related to the DTC while wiggling the wiring harness. Look for param-
eter values to change and/or a DTC to set.
Review the DRBIII

t Freeze Frame information. If possible, try to duplicate the

conditions under which the DTC was set.
Refer to any Technical Service Bulletins (TSB) that may apply.
Visually inspect the related wiring harness. Look for any chafed, pierced, pinched, or
partially broken wires.
Visually inspect the related wiring harness connectors. Look for broken, bent, pushed
out, or corroded terminals.
Were any of the above conditions present?

All

Yes

→ Repair as necessary

Perform POWERTRAIN VERIFICATION TEST VER - 1.

No

→ Test Complete.

215

DRIVEABILITY - SBEC

P1698-NO BUS MESSAGE FROM TRANS CONTROL MODULE —

Continued

Symptom:

P1899-P/N SWITCH STUCK IN PARK OR IN GEAR (4SP AUTO
TRNAS)

When Monitored and Set Condition:

P1899-P/N SWITCH STUCK IN PARK OR IN GEAR (4SP AUTO TRNAS)

When Monitored:

Continuously with the transmission in Park, Neutral, or Drive and

NOT in Limp-in mode.

Set Condition:

This code will set if the PCM detects an incorrect Park/Neutral switch

state for a given mode of vehicle operation. Two trip fault.

POSSIBLE CAUSES

INTERMITTENT PARK/NEUTRAL SWITCH

(T41) P/N POSITION SWITCH SENSE CIRCUIT SHORTED TO GROUND

(T41) P/N POSITION SWITCH SENSE CIRCUIT OPEN

TRANSMISSION RANGE SENSOR

POWERTRAIN CONTROL MODULE

TEST

ACTION

APPLICABILITY

1

Turn the ignition on.
With the DRBIII

t, read PCM DTCs.

Is the Good Trip displayed and equal to zero?

All

Yes

→ Go To 2

No

→ Go To 7

2

Turn the ignition on.
With the DRBIII

t, read the Park/Neutral Position Switch input state.

While moving the gear selector through all gear positions (Park to 1 and back to
Park), monitor the DRB display.
Did the DRBIII

t display show P/N and D/R in the correct gear positions?

All

Yes

→ Go To 7

No

→ Go To 3

3

Turn the ignition off.
Disconnect the PCM harness connector.
Disconnect the Transmission Range Sensor harness connector.
Measure the resistance between ground and the (T41) P/N Position Switch Sense
circuit.
Is the resistance above 100k ohms?

All

Yes

→ Go To 4

No

→ Repair the short to ground in the (T41) P/N Position Switch Sense

circuit.
Perform 41TE TRANSMISSION VERIFICATION TEST - VER 1..

216

DRIVEABILITY - SBEC

TEST

ACTION

APPLICABILITY

4

Turn the ignition off.
Disconnect the PCM harness connector.
Disconnect the Transmission Range Sensor harness connector.
Measure the resistance of the (T41) P/N Position Switch Sense circuit.
Is the resistance below 5.0 ohms?

All

Yes

→ Go To 5

No

→ Repair theopen in the (T41) P/N Position Switch Sense circuit.

Perform 41TE TRANSMISSION VERIFICATION TEST - VER 1..

5

Turn the ignition off.
Disconnect the PCM harness connector.
Move the Gear selector through all gear positions, from Park to 1st and back.
While moving the gear selector through each gear, measure the resistance between
ground and the (T41) P/N Position Switch Sense circuit.
Did the resistance change from below 10.0 ohms to above 10.0 ohms?

All

Yes

→ Go To 6

No

→ Replace the Transmission Range Sensor.

Perform 41TE TRANSMISSION VERIFICATION TEST - VER 1..

6

NOTE: Before Continuing: Disconnect the PCM harness connector and
check the related wiring terminals for corrosion, damage or terminal push
out. Repair as necessary.
Using the schematics as a guide, inspect the wire harness and connectors. Pay
particular attention to all Power and Ground circuits.
If there are no possible causes remaining, view repair.

All

Repair

Replace and program the Powertrain Module in accordance with
the Service Information.
Perform 41TE TRANSMISSION VERIFICATION TEST - VER 1..

7

At this time, the conditions required to set the DTC are not present.
NOTE: Use the Freeze Frame Data to help duplicate the conditions that set
the DTC. Pay particular attention to the DTC set conditions, such as, VSS,
MAP, ECT, and Load.
NOTE: Visually inspect the related wiring harness. Look for any chafed,
pierced, pinched, or partially broken wires.
NOTE: Visually inspect the related wiring harness connectors. Look for
broken, bent, pushed out, or corroded terminals.
NOTE: Refer to any technical service bulletins (TSB) that may apply.
Were any problems found?

All

Yes

→ Repair as necessary.

Perform 41TE TRANSMISSION VERIFICATION TEST - VER 1..

No

→ Test Complete.

217

DRIVEABILITY - SBEC

P1899-P/N SWITCH STUCK IN PARK OR IN GEAR (4SP AUTO TRNAS) —

Continued

Symptom:

*CHECKING PCM POWER AND GROUND CIRCUITS

POSSIBLE CAUSES

PCM FUSED B+ CIRCUIT

PCM FUSED IGNITION SWITCH OUTPUT CIRCUIT

PCM GROUND CIRCUITS

TEST

ACTION

APPLICABILITY

1

Turn the ignition off.
Disconnect the PCM harness connector.
Using a 12-volt test light connected to ground, probe the PCM Fused B+ circuit in the
PCM harness connector.
Does the test light illuminate brightly?

All

Yes

→ Go To 2

No

→ Repair the Fused B+ circuit.

Perform POWERTRAIN VERIFICATION TEST VER - 1.

2

Turn the ignition off.
Disconnect the PCM harness connector.
Turn the ignition on.
Using a 12-volt test light connected to ground, probe the PCM Fused Ignition Switch
Output circuit in the PCM harness connector.
Does the test light illuminate brightly?

All

Yes

→ Go To 3

No

→ Repair the Ignition Switch Output circuit

Perform POWERTRAIN VERIFICATION TEST VER - 1.

3

Turn the ignition off.
Disconnect the PCM harness connector.
Using a 12-volt test light connected to battery voltage, probe the PCM ground circuits
in the PCM harness connector.
Does the test light illuminate brightly?

All

Yes

→ Test Complete.

No

→ Repair the PCM ground circuits.

Perform POWERTRAIN VERIFICATION TEST VER - 1.

218

DRIVEABILITY - SBEC

 

 

 

 

 

 

 

Content   ..  52  53  54  55   ..