Daewoo Nubira. Service manual - part 23

 

  Index      Daewoo     Daewoo Nubira - service and repair manual

 

Search            

 

 

 

 

 

 

 

  

 

Content   ..  21  22  23  24   ..

 

 

Daewoo Nubira. Service manual - part 23

 

 

DOORS  9P – 7

DAEWOO V–121 BL4

Step

No

Yes

Value(s)

Action

20

Repair the open WHT wire.
Is the repair complete ?

System OK

21

Repair the open lock relay.
Is the repair complete ?

System OK

 

POWER WINDOWS (FRONT AND REAR)

Power Windows Do Not Operate

Step

Action

Value(s)

Yes

No

1

1.  Make sure the window lock switch on the driv-

er

'

s side door is not engaged. necessary.

2.  Test each of the power windows.

Does any power window operate ?

Go toStep 7

Go toStep 2

2

1.  At the driver

'

s side door, remove the power

window switch retaining screw.

2.  Lift up the power window switch to expose the

connector.

3.  Turn the ignition ON.
4.  Check the voltage at terminal 10 (ORN) of the

power window switch.

Is the voltage equal to the specified value ?

11––14 v

Go toStep 4

Go toStep 3

3

Repair the open power supply circuit to the driver

'

s

side door power window switch.
Is the repair complete

System OK

4

Use an ohmmeter to check the continuity between
ground and terminal 4 (BLK) of the driver

'

s side door

power window switch connector.
Is the continuity equal to the specified value ?

[

 0 

W

Go toStep 6

Go toStep 5

5

Repair the open circuit between ground and terminal
4 (BLK) of the driver

'

s side door power window

switch.
Is the repair complete

System OK

6

Replace the driver

'

s side power window switch.

Is the repair complete

System OK

7

1.  At the door with the inoperative power window,

remove the door trim panel.

2.  connect a fused jumper wire to the positive bat-

tery terminal.

3.  Connect another jumper wire to the negative

battery teminal.

4.  Disconnect the two––wire connector between

the window motor and the door harness.

5.  Connect the negative jumper wire to one of the

terminals of the two––wire connector.

6.  Touch the positive jumper wire to the other ter-

minal of the two––wire connector.

Does the window move up when the motor is pow-
ered directly by the battery, and down when the
jumper connections are reversed ?

Go toStep 9

Go toStep 8

8

Replace the window motor.
Is the repair complete

System OK

9P – 8

I

DOORS

DAEWOO V–121 BL4

Step

No

Yes

Value(s)

Action

9

Check the operation of the windows.
Is the driver

'

s side window the one that is inoperative

?

Go toStep 10

Go toStep 11

10

Replace the driver

'

s side door power window switch.

Is the repair complete

System OK

11

1.  Make sure the window lock switch on the driv-

er

'

s side door is not engaged.

2.  Turn the ignition ON.
3.  Backprobe to check the voltage at terminal 5

(DK BLU) of the driver

'

s side door power win-

dow switch.

Is the voltage equal to the specified value ?

11––14 v

Go toStep 12

Go toStep 10

12

1.  Make sure the window lock switch on the driv-

er

'

s side door is not engaged.

2.  Turn the ignition ON.
3.  Check the voltage at terminal 2 (PNK) of the

window switch connector for the inoperative
window.

Is the voltage equal to the specified value ?

11––14 v

Go toStep 14

Go toStep 13

13

Repair the open wire between the terminal 2 of the
window switch and the driver

'

s side door power win-

dow switch.
Is the repair complete

System OK

14

1.  At the inoperative window switch, use an ohm-

meter to check the continuity between ground
and terminal 4.

2.  At the inoperative window switch, use an ohm-

meter to check the continuity between ground
and terminal 1.

Are the continuities equal to the specified value ?

11––14 v

Go toStep 15

Go toStep 16

15

Replace the power window switch.
Is the repair complete

System OK

16

If one of the window switch wires tested in Step 14
does not show continuity with ground, use an ohm-
meter to test the continuity of that wire between the
window switch and the driver

'

s side door power win-

dow switch.
Is the continuity equal to the specified value ?

[

 0 

W

Go toStep 17

Go toStep 18

17

Replace the window switch for the inoperative win-
dow.
Is the repair complete ?

System OK

18

Repair the open circuit between the window switch
and the driver

'

s side power window switch.

Is the continuity equal to the specified value ?

[

 0 

W

Go toStep 21

Go toStep 20

DOORS  9P – 9

DAEWOO V–121 BL4

MAINTENANCE AND REPAIR

ON–VEHICLE SERVICE

FRONT DOOR GLASS RUN

Removal Procedure

1.  Remove the outside rearview mirror. Refer to Sec-

tion 9L, Glass and Mirrors.

2.  Remove the front door glass. Refer to Section 9L,

Glass and Mirrors.

3.  Remove the glass run.

Installation Procedure

1.  Install the glass run.
2.  Install the front door glass. Refer to Section 9L,

Glass and Mirrors.

3.  Install the outside rearview mirror. Refer to Section

9L, Glass and Mirrors.

REAR DOOR GLASS RUN

Removal Procedure

1.  Remove the rear door glass. Refer to Section 9L,

Glass and Mirrors.

2.  Remove the interior garnish molding.
3.  Remove the screws and the exterior garnish mold-

ing.

9P – 10

I

DOORS

DAEWOO V–121 BL4

4.  Remove the glass run.

Installation Procedure

1.  Install the glass run.

Notice :  Dissimilar metals in direct contact with each other
may corrode rapidly. Make sure to use the correct fasten-
ers to prevent premature corrosion.

2.  Install the exterior garnish molding with the screws.

Tighten

Tighten the rear door exterior garnish molding screws
to 1.5 N

S

m (13 lb–in).

3.  Install the interior garnish molding.
4.  Install the rear door glass. Refer to Section 9L,

Glass and Mirrors.

 

 

 

 

 

 

 

Content   ..  21  22  23  24   ..