Audi A4. Body repair manual - part 81
Interior lights, servicing
Interior/reading lights without sunroof switch
Notes:
To replace the bulb, pry off the lens.
Bulb for interior light -6-: 12 V, 10 W
Bulb for reading lights -5-: 12 V, 5 W
Removing
- Carefully pry off lens -1- using flat screwdriver.
- Remove both Phillips-head screws -2-.
- Pry out hooks at -B- using screwdriver and then remove
interior/reading light -3- from roof.
- Disconnect harness connector -4-.
Installing
- Connect harness connector -4-.
- Insert interior/reading light -3- at -A-, and clip it in on opposite side at -
B-.
- Secure with Phillips-head screws -2- and reinstall lens -1-.
Interior lights, servicing
Rear interior/reading lights, removing
and installing (sedan)
Notes:
To change bulbs, remove the rear reading
lights.
Bulb for reading light: 12 V, 5 W (2x)
Removing
- Carefully pry out interior/reading light -1- using flat screwdriver.
- Disconnect harness connector -2-.
Installing
- Install in reverse order of removal.
Interior lights, servicing
Trunk lights, removing and installing
Notes:
To change bulbs, remove trunk lights.
Bulb for trunk light: 12 V, 5 W (2x)
Removing
- Carefully pry out trunk light -1- using flat screwdriver.
- Disconnect harness connector -2-.
Installing
- Install in reverse order of removal.
Interior lights, servicing
Glove compartment light, removing and
installing
Notes:
To change bulbs, remove glove compartment
light.
Bulb for glove compartment light: 12 V, 5 W
Removing
- Carefully pry out glove compartment light -1- using flat screwdriver.
- Disconnect harness connector -2-.
Installing
- Install in reverse order of removal.
Interior lights, servicing
Footwell lights, removing and installing
Note:
To change bulbs, remove footwell lights.
Bulb for footwell light: 12 V, 5 W (2x)
Removing
- Carefully pry out footwell light -1- using flat screwdriver.
- Disconnect harness connector -2-.
Installing
- Install in reverse order of removal.
Interior lights, servicing
Vanity mirror light, removing and
installing
Note:
The vanity mirror light is integrated into the sun
visor. The entire sun visor must be replaced
when there is a malfunction.
- Remove sun visor.
Repair Manual, Body Interior, Repair Group
70
Interior lights, servicing (Avant)
Interior lights, servicing (Avant)
CAUTION!
Disconnect the battery Ground (GND) strap
before working on the electrical system.
Notes:
Before disconnecting the battery, determine the
correct coding for the anti-theft radio.
After reconnecting the battery, check and
activate the vehicle's electrical equipment
(radio, clock, comfort and convenience features,
etc.) as outlined in this Repair Manual or the
Owner's Manual.
Interior lights, servicing (Avant)
Complete overview
1 - Cargo area light
2 - Rear interior/reading light, right and left
sides
3 - Bulb for reading light
12 V, 5 W
4 - Catch
5 - Positioning hooks (2x)
6 - Reading light harness connector
7 - Positioning hooks (2x)
8 - Cargo area light harness connector
9 - Catch
10 - Bulb for cargo area light
12 V, 10 W
Interior lights, servicing (Avant)
Rear interior/reading lights, removing and
installing
Removing
- Using screwdriver, carefully pry out
interior/reading light -2- from roof at catch -4-.
- Disconnect harness connector -6-.
- Remove bulb -3- from socket.
Installing
- During installation, insert positioning hooks -5-
and, on opposite side, make sure that catch -4-
engages audibly.
- Remainder of installation is in reverse order of
removal.
Interior lights, servicing (Avant)
Cargo area light, removing and installing
Removing
- Using screwdriver, carefully pry out cargo area
light -1- from roof at catch -9-.
- Disconnect harness connector -8-.
- Remove lens from lamp holder.
- To change bulb, remove bulb from clamp-type
socket.
Installing
- During installation, insert positioning hooks -7-
and, on opposite side, make sure that catch -9-
engages audibly.
- Remainder of installation is in reverse order of
removal.
Lock cylinder heating, servicing
Lock cylinder heating,
servicing
CAUTION!
Disconnect the battery Ground (GND) strap
before working on the electrical system.
Notes:
Before disconnecting the battery, determine
correct coding for the anti-theft radio.
After reconnecting the battery, check and
activate the vehicle's electrical equipment
(radio, clock, comfort and convenience
features, etc.) as outlined in this Repair Manual
or the Owner's Manual.
Lock cylinder heating, servicing
Heated door lock control module,
removing and installing
Removing
- Remove door trim.
Repair Manual, Body Interior, Repair Group
70
- Remove screws -2- from plastic nuts -3-.
- Disconnect harness connector and remove control module -1-.
Installing
- Install in reverse order of removal.
Relay panel, fuse panel
Relay panel, fuse panel
CAUTION!
Disconnect the battery Ground (GND) strap
before working on the electrical system.
Notes:
Before disconnecting the battery, determine the
correct coding for the anti-theft radio.
After reconnecting the battery, check and
activate the vehicle's electrical equipment
(radio, clock, comfort and convenience
features, etc.) as outlined in this Repair Manual
or the Owner's Manual.