Snowmobile Polaris Rush (2010 year). Instruction - part 8

 

  Index      Snowmobiles / ATV     Snowmobile Polaris Rush - instruction 2010 year

 

Search            

 

 

 

 

 

 

 

 

 

Content   ..  6  7  8  9   ..

 

 

Snowmobile Polaris Rush (2010 year). Instruction - part 8

 

 

33

FEATURES

Instrument Cluster

Rider Information Center

Odometer/Engine Hour Display Area
This area displays the odometer, Trip A meter, Trip B meter and engine 

hours meter.
The odometer displays the total distance traveled by the vehicle since 

manufacture. Each trip meter records the distance traveled by the vehi-

cle on a trip if the meter is reset before each trip. The engine hour meter 

displays the total hours the engine has been in operation since manufac-

ture.
To change the display, press and release the SELECT button or the SET 

switch until the desired item is displayed.
To reset a trip meter, press and hold the SELECT button or the SET 

switch until the meter resets to zero.
Playback Function
The playback function allows the rider to record and play back engine 

speed, vehicle speed and throttle position sensor information for up to 

three minutes.
1. To begin recording, simultaneously press and hold the MODE and 

SELECT buttons on the instrument cluster for three seconds. The 

playback indicator will flash while the instrument cluster is record-

ing.

2. To play back the recorded data, stop the vehicle and wait for engine 

speed to drop below clutch engagement.

3. Simultaneously press and release the MODE and SELECT buttons 

on the instrument cluster.

4. Applying the throttle will clear the display and return the instrument 

cluster to normal operation.

34

FEATURES

Instrument Cluster

Rider Information Center

Standard/Metric Display
The odometer and temperature displays can be viewed in either standard 

or metric units of measurement. Both displays change if units are 

changed. The new settings will remain until changed by the operator.
Change Method 1
1. Press and release the MODE button or MODE switch until engine 

temperature displays.

2. Press and hold the MODE button or MODE switch until the units 

change.

Change Method 2
1. Press and release the SELECT button or SET switch until the 

odometer displays.

2. Press and hold the SELECT button or SET switch until the units 

change.

35

FEATURES

Instrument Cluster

Rider Information Center

Diagnostic Display Mode
The diagnostic display mode is for informational purposes only. Please 

see your Polaris dealer for all major repairs. 
The diagnostic mode is accessible only when the check engine warning 

indicator is illuminated and a diagnostic code is active.
Do not stop the engine if you want to view the active code (failure 

code). Active codes cannot be retrieved if power is interrupted to the 

instrument cluster. The codes will become inactive codes if power is 

interrupted. Inactive codes are stored in the history of the unit. Please 

see your Polaris dealer to retrieve inactive codes.
Use the following procedure to view active codes.
1. Do not stop the engine.
2. Press and release the SELECT button or SET switch to toggle to the 

diagnostic display mode. When a code is active, the diagnostic dis-

play mode will appear immediately following the engine hour dis-

play. 

TIP: When the diagnostic mode is displayed, the check engine warning indicator 

will begin to flash.

3. A set of two numbers will appear in the display. 

• The 2-6 digit suspect parameter number (SPN) in the information display 

area indicates which component is generating the fault code.

• The 1-2 digit failure mode indicator (FMI) number in the odometer area 

indicates the fault mode, such as open or short circuit. 

4. More than one fault may be active. Press and hold the MODE but-

ton or MODE switch for two seconds to toggle to the next active 

code. Repeat until all codes are retrieved.

5. See page 36 for code definitions and failure descriptions.

36

FEATURES

Instrument Cluster

Rider Information Center

Diagnostic Display Code Definitions
Open Load: There is a break in the wires that lead to the item listed in 

the chart (injector, fuel pump, etc.), or the item has failed.
Short-to-Ground: The wire is shorted to ground between the electronic 

control unit and the item listed in the chart. 
Shorted Load: The wires leading to the item listed in the chart are 

shorted together, or the item has shorted internally. 
Short-to-Battery: The wire leading from the item listed in the chart to 

the electronic control unit is shorted to a wire at battery voltage.

Diagnostic Codes

Component

Condition

SPN

FMI

Throttle Position Sensor

 

Voltage Too High

51

3

Voltage Too Low

4

Abnormal Rate of Change

10

Engine Temperature Sensor

 

Voltage Too High

110

3

Voltage Too Low

4

Temperature Too High

16

Engine Overheat Shutdown

0

Temperature Above Normal Range

15

Intake Air Temperature Sensor

 

Voltage Too High

105

3

Voltage Too Low

4

Barometric Pressure Sensor

 

Voltage Too High

108

3

Voltage Too Low

4

Exhaust Temperature Sensor

 

Voltage Too High

173

3

Voltage Too Low

4

Crankshaft Position Sensor

Circuit Fault

636

8

Plausibility Fault

2

Knock Sensor 1

Voltage Too Low

731

4

Vehicle Speed Sensor 

Vehicle Speed Too High

84

0

Vehicle Speed Too Low

1

Data Erratic, Intermittent or Missing

2

Injector 1 (MAG) (SDI Part 

Load)

Driver Circuit Open/Grounded

651

5

Driver Circuit Short to B+

3

Injector 2 (PTO) (SDI Part Load) Driver Circuit Open/Grounded

652

5

Driver Circuit Short to B+

3

 

 

 

 

 

 

 

Content   ..  6  7  8  9   ..