Snowmobile Polaris 800 RMK / 800 Pro-RMK / 800 RMK (2010 year). Instruction - part 16

 

  Index      Snowmobiles / ATV     Snowmobile Polaris 800 RMK / 800 Pro-RMK / 800 RMK - instruction 2010 year

 

Search            copyright infringement  

 

 

 

 

 

 

 

 

 

Content   ..  14  15  16  17   ..

 

 

Snowmobile Polaris 800 RMK / 800 Pro-RMK / 800 RMK (2010 year). Instruction - part 16

 

 

65

OPERATION

Electronic Reverse (PERC)

Engaging Reverse

1. Stop the snowmobile and leave the engine idling.

2. Make sure the area behind your vehicle is clear.

3. Push the yellow reverse button on the left-hand control for one sec-

ond, then release. The engine will automatically reduce RPM and 
start a reverse rotation. A flashing reverse light on the instrument 
panel will indicate that the transmission is in reverse.

4. Apply the throttle slowly to make sure the transmission is in 

reverse.The maximum engine RPM will be 6000 when in reverse. 

TIP: If the engine stops running, the snowmobile will be in forward gear when it's 

restarted.

Disengaging Reverse

1. Stop the snowmobile and leave the engine idling.

NOTICE: Engaging the starter when the engine is running WILL result in serious 

engine damage, especially if the transmission is in reverse. Never 
engage the starter when the engine is running.

2. Push the yellow reverse button for one second and release. The 

engine will slow and begin to rotate forward. The light on the instru-
ment panel will shut off.

3. Apply the throttle slowly to make sure the transmission is in for-

ward.

66

OPERATION

Emergency Stopping

The following chart lists methods for stopping the snowmobile in the 
event of an emergency. See page 62 for more information about the 
engine stop switch and throttle safety switch.

SYSTEM

WHAT IT DOES

Ignition Switch

Interrupts ignition circuit

Brake

Slows jackshaft

Engine Stop Switch

Interrupts ignition circuit

Throttle Safety Switch

Interrupts ignition circuit

Tether Switch (Option)

Interrupts ignition circuit

67

OPERATION

Daily Storage

At the end of each ride, park the snowmobile on a level surface and sup-
port it at the rear with an appropriate track stand. The track should be 
suspended approximately 4I (10 cm) off the ground.

Remove the key and cover the snowmobile.

Towing

For your safety, do not attempt to use a tow hitch until you've read the 
following warnings and understand the proper hitch functions.

WARNING! Objects towed with a rope have no braking power and can easily 
collide with the rear of the snowmobile or other objects, resulting in serious 
injury or death. DO NOT tow toboggans, sleds, saucers, or any type of vehicle 
with a rope. Only a stiff metal pole connecting the towed object and the tow hitch 
on the snowmobile should be used. If passengers are to be towed on a 
toboggan or sled, make sure the pole is at least four feet (1.2 meters) long to 
prevent any possibility of contact between the snowmobile's track and a person 
riding in the towed object.

WARNING! Braking distances increase when towing loads. Slow down to 
maintain control of the snowmobile.

If the snowmobile becomes inoperable and must be towed, and if it isn't 
possible to use a rigid tow bar, attach the tow rope to the ski spindles 
(not to the ski loops) to prevent damage to the steering components. 
Remove the drive belt before towing, and have someone ride on the 
towed snowmobile to operate the brake and steering when necessary.

NOTICE: Towing a disabled snowmobile with the drive belt in place can result in 

serious damage to the engine and drive system. Always remove the 
drive belt from a disabled snowmobile before towing.

68

MAINTENANCE

Emission Control Information

Any qualified repair shop or qualified person may maintain, replace, or 
repair the emission control devices or systems on your snowmobile.

Emission Control Label

Your snowmobile is equipped at the time of sale with an emission con-
trol information (ECI) label and a factory-installed emissions informa-
tion hangtag. These items are required by U.S. Environmental 
Protection Agency regulations. The ECI label is permanently affixed to 
either the right side of the tunnel or the engine recoil cover. The ECI 
label should not be removed, even after you purchase the snowmobile. 
You may remove the factory-installed emissions information hangtag, 
which is intended solely for your use in making a purchasing decision.

Emission Control Maintenance Requirements

Your snowmobile is certified to operate on gasoline with a minimum 
octane level of 87 (R+M)/2. If your snowmobile is equipped with a 
check engine light and it comes on, you must take your snowmobile to a 
qualified dealer for diagnostic service. Specifications and adjustments 
for engine tune-ups are located in the Service Manual, which is avail-
able to your qualified service technician. Reverse (if equipped) must not 
be engaged during engine tune-ups.

Owner's Responsibilities

Please read the Snowmobile Engine Emissions Limited Warranty, and 
read the maintenance section of your owner's manual. You are responsi-
ble for ensuring that the specified maintenance is performed. POLARIS 
recommends that you contact an authorized POLARIS dealer to perform 
any service that may be necessary.

Non-ionizing Radiation

This vehicle emits some electromagnetic energy. People with active or 
non-active implantable medical devices (such as heart monitoring or 
controlling devices) should review the limitations of their device and the 
applicable electromagnetic standards and directives that apply to this 
vehicle.

 

 

 

 

 

 

 

Content   ..  14  15  16  17   ..