Daewoo Nubira. Service manual - part 173

GLASS AND MIRRORS  9L – 7

DAEWOO V–121 BL4

Step

No

Yes

Value(s)

Action

12

Replace the outside rearview mirror switch.
Is the repair complete?

System OK

13

1.  On the side which has the inoperative mirror,

remove the black plastic escutcheon from the
trim panel side of the door.

2.  Disconnect the outside mirror electrical con-

nector.

3.  Turn the ignitionON.
4.  At the outsidemirrorconnector, connect a volt-

meterbetween terminal 1 (GRY)and terminal 2
(LTGRN, if testing the left side; orPPL/WHT, if
testing the right side).

5.  Operate the in/out adjustment on the switch,

and record the voltage indicated in each switch
position.

6.  Connect a voltmeterbetween terminal 1 (GRY)

and terminal 3 (WHT, if testing the left side; or
RED/WHT, if testing the right side).

7.  Operate the up/down adjustment on the switch,

and record the voltage indicated in each switch
position.

Does the voltmeter indicate the specified voltage for
each test, with the polarity reversing when the switch
is changed fromin to out, or up to down?

11–14 v

Go to Step 14

Go to Step 15

14

Replace the outside rearview mirror.
Is the repair complete?

System OK

15

1.  Remove the retaining screw for the power door

mirror and power window switch assembly.

2.  Lift the switch assembly so the connectors on

the underside are visible.

3.  Leave the outside mirror disconnected, but do

not disconnect the mirror switch connector.

4.  Turn the ignitionON.
5.  At themirrorswitch connector, backprobe to

measure the voltage between terminal 1 (GRY)
and terminal 2 (LTGRN, if testing the left side;
or PPL/WHT, if testing the right side).

6.  Operate the in/out adjustment on the switch,

and record the voltage indicated in each switch
position.

7.  Connect a voltmeterbetween terminal 1 (GRY)

and terminal 3 (WHT, if testing the left side; or
RED/WHT; if testing the right side).

8.  Operate the up/down adjustment on the switch,

and record the voltage indicated in each switch
position.

Does the voltmeter indicate the specified voltage for
each test, with the polarity reversing when the switch
is changed fromin to out or up to down?

11–14 v

Go to Step 16

Go to Step 12

16

Repair the open circuit between the mirror switch
and the outside rearview mirror connector.
Is the repair complete?

System OK

 

9L – 8

I

GLASS AND MIRRORS

DAEWOO V–121 BL4

MAINTENANCE AND REPAIR

ON–VEHICLE SERVICE

WINDSHIELD

Tools Required

J–24402 Glass Sealant Remover

Removal Procedure

1.  Remove the cowl vent grille. Refer to Section 9R,

Body Front End.

2.  Remove the inside rearview mirror. Refer to”Inside

Rearview Mirror” in this section.

3.  Remove the weatherstrip around the windshield.
4.  Using the glass sealant remover J–24402, cut the

adhesive around the windshield.

5.  Remove the windshield from the vehicle..
6.  Using a knife, remove the adhesive from the wind-

shield.

7.  Using a knife, remove the adhesive from the wind-

shield frame.

GLASS AND MIRRORS  9L – 9

DAEWOO V–121 BL4

Installation Procedure

1.  Install the new weatherstrip to the windshield.

2.  Apply tape to the new weatherstrip and the wind-

shield to hold the weatherstrip in place.

3.  Apply adhesive primer to the windshield frame and

the perimeter of the windshield.

4.  Apply glass adhesive to the windshield frame.
5.  Install the windshield into the windshield frame.
6.  Reposition the tape over the weatherstrip, the wind-

shield, and the windshield frame to hold the wind-
shield in place.

7.  Let the adhesive dry for 24 hours.
8.  Remove the tape.
9.  Check for waterleaks by pouring water on the wind-

shield. If a leak is found, dry the windshield and fill
the area that leaks with adhesive. If the leak per-
sists, remove the windshield and repeat the entire
procedure.

10.  Install the inside rearview mirror. Refer to”Inside

Rearview Mirror” in this section.

11.  Install the cowl vent grille. Refer to Section 9R,

Body Front End.

9L – 10

I

GLASS AND MIRRORS

DAEWOO V–121 BL4

REAR WINDOW GLASS

(Notchback Shown, Hatchback and
Wagon Similar)

Tools Required

J–24402 Glass Sealant Remover

Removal Procedure

1.  Disconnect the negative battery cable.
2.  Remove the rear window wiper (wagon only). Refer

to Section 9D, Wipers/Washer Systems.

3.  Disconnect the rear window defogger electrical con-

nector.

4.  Remove the weatherstrip around the rear window.

5.  Using the glass sealant remover J–24402, cut the

adhesive around the rear window.